Patterns, or gobos, are widely used by designers in theatre, film, photography and television to create atmosphere, project scenery, and generally enhance the visual impact of their lighting.

Conceived by some of the world's leading lighting designers, the Rosco range presently includes hundreds of standard steel gobo designs.

To insure design integrity the patterns are etched using a precise double-sided process on stainless steel. The result is durable, high quality patterns which will withstand the extreme heat at the gate of ellipsoidal spotlights.

Rosco steel gobos are round to allow for rotation in the gate when aligning the projected image.

The standard "B" size is suitable for most fixtures with a 6" lens when used with a Rosco Pattern Holder or the holders of other manufacturers.

Trimming of patterns, where necessary, can be easily accomplished with a pair of scissors.

Related Questions and Answers

Q: 1. Is this compatible with a Canon Scoopic?

A: Yes, it will work with the Canon Scoopic.

Q: 2. Would this work in an external chassis

A: This question is chipset specific so it will not work with every external chassis, if any.

Q: 3. What is the dynamic range of this film?

A: Unfortunately Kodak does not provide a dynamic range for this film. This is the data they provide: https://bhpho.to/48gN4gp

Q: 4. Will this work with a Midland GXT100 VP4? I was hoping there was some kind of standard for these plugs.

A: Otto Engineering products are compatible with Motorola devices and Motorola voltage and pin configurations. They are not recommended or designed for Midland products.

Q: 5. Does this rack take cage nuts or cage clips to install equipment on the rails? I see the rails have slight circular threads in them but is that enough to house equipment with a standard 10-32 screw or are cage nuts needed?

A: This rack comes standard with (2) pairs of 11-gauge threaded, 10-32 rackrails with EIA spacing and labeled rackspace increments. Electrical knockouts on rear plates (both top and bottom) can easily be removed to pass cables (includes 1/2", 3/4", 1" and 1-1/2" openings). The configurable, open top also includes a UHF/VHF knockout. Pre-Installed Washers Pre-installed washers on all 10-32 threaded rackscrews save installation time. Cabinet Accepts 19" Equipment (Width) Depth 24" Capacity 64-3/4" (37U)

Q: 6. What size clamp would you recommend for clamping a sound blanket?

A: The size clamp you will need will depend partly onto what item you will be clamping the sound absorption blanket. If you are clamping it to a pipe, you would have to take into consideration the diameter of the pipe, as the jaws have to be wide enough to go around the pipe, as well as to hold the blanket. As a catch-all recommendation, I would typically recommend the Impact 2" Steel Spring A-Clamp (Black), B&H # IMSSCA20B • MFR # SSC-A20B, over the smaller Impact 1" Steel Spring A-Clamp (Black) due to its larger size and extra flexibility.

Q: 7. Is this the same spec as the rods used in hollywood arms?

A: Yes. The following unit will adapt to any grip head on the market.

Q: 8. What is the peg on the reel? I bought one that has a diamond on it that the peg sits in but the orginal reel that was in the camera has a circle for the peg. (I have a bolex h16 movie camera 16mm)

A: Bolex H16 cameras have spindles with square posts. Kodak daylight spools have a square hole for Kodak Eastman Double-X Black-and-White Negative Film 7222 (16mm, 100' Roll, Single Perf). We are not familiar with any spool that has a circle.

Q: 9. How tall is this without the wheels?

A: Roughly 17 without and 21 with

Q: 10. what is the asa rating?

A: You can find Kodak's exposure chart here http://bit.ly/2ma7hSI.