Designed to eliminate the extra step of finishing the screen with trim, the 220V 24708ELSI Tensioned Advantage Electrol 65 x 116" Ceiling-Recessed Motorized Screen from Da-Lite is designed with ceiling trim already in place. Once the screen is installed, the screen's trim conceals the rough opening eliminating the need to complete additional trim work. Sliding installation brackets are included to make it easy to attach the screen housing to the structure above the drop ceiling.

The Advantage Electrol screen features simple in-ceiling installation that can be done in two stages. The screen case can be installed during the rough-in construction stage and the fabric assembly can be completed during the finishing stage.

133" Diagonal / 16:9 Aspect Ratio    HD Progressive 1.3 Screen Surface    1.3 Gain / 150° Viewing Angle    Slim-Tab Tensioning System    White Powder-Coated Case    Installs Above the Ceiling    Black Backing Standard    Silent Motor    Video Projector Interface    Low Voltage Control (LVC)

Ideal for applications where projector brightness and screen size require an increase in gain, the white surface offers high-fidelity color reproduction, and allows for more flexibility with ambient light conditions. This surface works for video as well as charts and graphs in a corporate setting. Cone 150° Gain: 1.3

• Smooth Roll Technology to keep your screen flat
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension

• UL Plenum rated case
• White powder-coated case for a clean aesthetic
• Black-backed screen material for enhanced image quality and opacity
• Seamless surface

Designed to provide silent operation when raising or lowering the screen

Allows projectors with 5 or 12V LVC leads to automatically trigger the screen to raise or lower whenever the projector is turned on or off

Allows the included wall switch, as well as devices such as automation systems, third-party wall switches, and remotes that support LVC, to raise or lower the screen remotely

Related Questions and Answers

Q: 1. Does this light unit have a slave so that both lights flash at the same time?

A: Both lights do. Each plugs into the wall separately and a supply synch cord plugs ininto one of thelights you chose. When the shutter goefires that light and the other light fires through the slave trigger works greats the light plugged into the one light

Q: 2. I just received my impact EX-100A monolight today. And realized my cord is a European cord. I wanted to know if I am able to get an adapter for it so that it works, or do I have to return it?

A: Hi Sharlene, you have bought the 220V AC unit, so, you must know if where you are you have that electricity. If you are, you just need to buy the adapter. I have used mine in Chile where the electricity comes at 220V AC, but I needed an adapter to plugging in.

Q: 3. I have set this up and use an on-camera flash to trip the two lights BUT I am NOT able to vary the output of the flash. I dial from full to 1/8 but only the modeling light varies in intensity. Am I doing something wrong?Lucian

A: Just to be sure - when reducing flash power, you must dump the flash first and then measure power. This means if the flash is at full power and you reduce it to an 1/8, you must first fire a flash to dump the power out of the flash capacitors and reduce their charge to an 1/8 and then measure your flash output. If the flash remains at full for a 3rd and 4th shot, then it may be faulty.

Q: 4. I was just wondering if anyone has replaced the modelling lamp with an LED light bulb? I imagine you could get a lot more light output from an LED bulb, especially a cree bulb. I understand it would have to be the dimmable variety...

A: It has not been tested by the manufacture. It is not recommended to do that as you can damage the electronics if there is a compatibility issue.

Q: 5. Can these lights be on for a full shoot, or are they flash/strobe only? Looking to purchase something inexpensive for filming purpose, and won't need the flash setting.

A: You could use the modeling lights for filming but it's probably cheaper to just by led modeling lights with more wattage. I think the modeling lights on this kit is about 60 watts. Modeling lights are used to see the lighting and to help your camera focus on the subject.

Q: 6. I have a Nikon D3300, Do I need to buy the PowerTrigger transmitter in order to make the Flash work? Or the sync cord will do the job.

A: I am not familiar with Nikon but I can tell you that the sync cord works with my Canon DSLR. As long as there is an outlet on the side of the camera, which there should be, it should work fine.

Q: 7. two strobes, two soft boxes, two stands and one sync cord- Are they included in this kit?

A: This kit would include two Impact EX 100 monolights, two softboxes with speed rings, two sync cables, two power cords, flashtube/modeling lamp for each head, a reflector for each head, spare fuses for each head, Impact 8 ft light stands and a 1 year warranty on each head.

Q: 8. can this light be triggered by another flash?

A: Yes, the nature of it is that it's triggered by a flash. I have three of them, so I connect directly to one through a cord, and that one triggers the other two. But I have also found that my bounce flash will trigger any of them as well, and I think that's what you're asking about.

Q: 9. Can this be used for outdoor portraits?

A: Probably not unless there is an outlet or something to plug into

Q: 10. Will this work with the remote wireless flash signal produced by the OMD EM-10?

A: I'm unfamiliar with that specific wireless trigger system, but I have used two different wireless triggers with this light kit successfully. As long as the trigger uses a 1/8 mono plug, you should be fine. If not, you can buy adapters to make these things work.