Patterns, or gobos, are widely used by designers in theatre, film, photography and television to create atmosphere, project scenery, and generally enhance the visual impact of their lighting.

Conceived by some of the world's leading lighting designers, the Rosco range presently includes hundreds of standard steel gobo designs.

To insure design integrity the patterns are etched using a precise double-sided process on stainless steel. The result is durable, high quality patterns which will withstand the extreme heat at the gate of ellipsoidal spotlights.

Rosco steel gobos are round to allow for rotation in the gate when aligning the projected image.

The standard "B" size is suitable for most fixtures with a 6" lens when used with a Rosco Pattern Holder or the holders of other manufacturers.

Trimming of patterns, where necessary, can be easily accomplished with a pair of scissors.

Related Questions and Answers

Q: 1. Does it work with only Intel SSD s... What about samsung or corsair's ssds

A: This is universal and works with any brand M.2 ssd.

Q: 2. Can I take this through airport security without it getting ruined by the x-Ray machine?

A: I'm not sure, but whenever I take film through an airport, I ask them not to put it through the x-ray scanner and they comply. I'm sure you could do the same here.

Q: 3. Will this work with the ROG Zenith II Extreme Alpha?

A: Yes that board is supported. https://www.asus.com/support/FAQ/1037507

Q: 4. Can we use Sabrent 8TB Rocket Q M.2 2280 Internal SSD with this controller?

A: Please see here for motherboard and SSD compatibility.

Q: 5. Will this work in a Sonnet Echo Express III-D Thunderbolt 3 Expansion Chassis for PCIe Cards? If so, how would it perform (eg read/write speeds, raid configs)?

A: It is not yet on the list of Sonnet recommended cards. Sonnet does have their own supported: https://www.bhphotovideo.com/c/product/1565788-REG/sonnet_fus_ssd_4x4_e3s_m_2_4x4_pcie_3_0.html https://www.bhphotovideo.com/c/product/1565788-REG/sonnet_fus_ssd_4x4_e3s_m_2_4x4_pcie_3_0.html As far as others please see this link for further info: https://sonnettech.com/support/downloads/manuals/M2_compatibility.pdf

Q: 6. Will this allow four Gen4 Nvme cards to work simultaneously at Gen4 speed on the Asus Maximus Hero Z790 motherboard?

A: Yes, the ASUS Hyper M.2 x16 Gen5 Card can sustain Gen 4 speeds for the connected M.2 drives.

Q: 7. Will this work on the Asus Rog Zenith II Extreme Alpha?

A: Yes, this will work on the motherboard. There are 4 PCIe 4.0 x16.

Q: 8. Does this rack take cage nuts or cage clips to install equipment on the rails? I see the rails have slight circular threads in them but is that enough to house equipment with a standard 10-32 screw or are cage nuts needed?

A: This rack comes standard with (2) pairs of 11-gauge threaded, 10-32 rackrails with EIA spacing and labeled rackspace increments. Electrical knockouts on rear plates (both top and bottom) can easily be removed to pass cables (includes 1/2", 3/4", 1" and 1-1/2" openings). The configurable, open top also includes a UHF/VHF knockout. Pre-Installed Washers Pre-installed washers on all 10-32 threaded rackscrews save installation time. Cabinet Accepts 19" Equipment (Width) Depth 24" Capacity 64-3/4" (37U)

Q: 9. Is this compatible with the new generation threadripper trx40 motherboards by Asus?

A: Yes, it is supported on any motherboard that supports PCIe slot.

Q: 10. Does this use x4 PCI lanes per M2 drive installed on the card? So, if you have 4 drives on this, it will be using up 16 total lanes?

A: Generally that is the configuration. However the PCIe lane allocation may change based on the motherboard being used.