The SSM from Lectrosonics is a miniature Digital Hybrid Wireless Transmitter with selectable frequencies across a maximum tuning range of 76.7 MHz and has selectable 25 or 50 mW RF output power. It can be used in applications where concealment in costuming is required or any other production such as for live stage, theater, houses of worship, reality TV, and more.

The SSM features selectable frequencies in 100 kHz or 25 kHz steps yielding a total of 3,072 available frequencies across three standard frequency blocks. Its lithium-ion battery provides power and sits in a stainless-steel battery door that latches closed and cannot be jarred open accidentally.

The servo bias input that is built into the transmitter accepts mic or line level signals and uses gain adjustments in 1 dB steps. The LED indicators on the membrane keypad allow you to monitor precise gain adjustments and settings. A built-in limiter in the preamp, handles signal peaks over 30 dB. This provides you with the maximum signal to noise ratio and minimum distortion for input, but still provides protection against input overloads.

The SSM is compatible with earlier analog Lectrosonics receivers IFB, and some other receivers, from manufacturers that utilize the DSP emulation mode, which is selectable in the LCD menu. The SSM transmitter housing is constructed of machined aluminum and has a hard, black electroless nickel finish called ebENi.

Miniature SSM Bodypack Transmitter    Voice Technologies VT500 Omni Lav Mic    Removable Belt Clip    Alligator Clip    Dracula Mount    Windscreen    Tie Tac Clip    3.7V Lithium-Ion Battery Pack    Includes Battery Charger    Includes Carrying Case

The SSM transmitter tunes across a range of over 76 MHz. This tuning range covers three standard Lectrosonics frequency blocks

The transmitter operates from a 3.7V rechargeable battery that will provide about four hours of operation per charge

The factory-supplied battery charger provides a folding NEMA 2-prong plug, and will operate from 100-240 VAC sources. The LED glows red during charging and turns green when the battery is fully charged

The LCD is a numeric-type Liquid Crystal Display with screens for adjusting output power, frequency, audio level, low frequency audio roll-off, and various modes and options

The antenna is a flexible whip made of galvanized steel, permanently attached to the transmitter to prevent damage from heavy use. The IR port is capped with a translucent dome material to broaden the reception angle. The input jack is a rugged 3-pin LEMO connector with a threaded locking sleeve

An infrared sync port on the SSM allows for quick setup with compatible receiver systems. A micro-B USB port makes it possible for firmware updates in the field as advanced features are added in the future

The SSM responds to remote commands for frequency, audio level, sleep modes, and other settings from the RM remote unit or 3rd party smartphone apps

Related Questions and Answers

Q: 1. Can you use this with a SRa receiver

A: So long as your SRa receiver has the same frequency ranges as the LMb transmitter, the LMb transmitter will work with an SRa receiver.

Q: 2. What is the effective range of the LMB B1 Transmitter? By range I mean distance between transmitter and receiver not frequency range.

A: The operating distance for the Lectrosonics LMb Bodypack Wireless Transmitter and a compatible wireless receiver is approximately 328 feet line of sight.

Q: 3. What recivers are available to use with this transmitter?

A: The list of receivers compatible with the Lectrosonics HMa Plug-On Wireless Transmitter depends on the frequency range selected. For an HMa on the A1 (470-537MHz) or B1 (537-607MHz) ranges, there are many options including the Lectrosonics SRc, LR, UCR411A. If using the HMa on the 941 (941-951MHz), the options are limited to the SRc receiver.

Q: 4. I have a lot of Sennheiser lavs with a 3.5mm connector. Is there an adapter that will connect my Sennheiser mics to the 3 pin lemo of this receiver?

A: Unfortunately there would be no adapters available to connect a lavalier wired with a Sennheiser mini jack to connect with a Lectrosonics transmitter.

Q: 5. Is it posible to use this Lectrosonic transmitter with a Sennheiser receiver in the same band (A1)?

A: No that would not be possible.

Q: 6. Is there a battery eliminator made for this?

A: No,at this time there are no battery eliminators or alternate powering options available for the LMb transmitter.

Q: 7. Do non servo ta5f connectors work with the lmb transmitter?

A: Yes, the Lectrosonics L-Series LMb Bodypack Wireless Transmitter and all other Lectrosonics transmitters with 5-pin inputs have servo bias inputs that can also be used with other conventional wiring configurations.

Q: 8. Is there an adapter for lectrosonics compatible (TA5F) lavs, or would I need to get new lavs for this?

A: Although we have seen custom adapters to convert TA5F to 3-Pin Lemo, we recommend using lavaliers with dedicated wiring for the Lectrosonics SSM Digital Hybrid Wireless Miniature Transmitter. B&H does not offer adapters of this nature at this time.

Q: 9. Does this run off of 9V battery power?

A: You would need SR9VBP to be able to run this on a 9V battery. https://www.bhphotovideo.com/c/product/663969-REG/Lectrosonics_SR9VBP_SR9VBP_9_Volt_Battery.html

Q: 10. Will this work with the LR’s single A1 band? I’m eventually going to purchase the Lectrosonics DSR I only have LT now

A: No, the Lectrosonics DBSM Single-Battery Digital Wireless Bodypack Transmitter/Recorder is not compatible for use with the Lectrosonics LR Camera-Mount Wireless Receiver. The DBSM is only compatible with the Lectrosonics DSR, DSR4, and DSR5P Digital Slot Receivers.