The Opteka CXS-1000 portable stabilizing system is a unique stabilizing system which provides all the stabilization of a 70" equivalent tripod or monopod with the portability of being able to fit right in your pocket. The CXS-1000 uses a retractable tethered cable which may be locked at your desired length. The end of the cable features a plate which is secured under your shoe creating the necessary tension to stabilize any camera or camcorder.

• Mimics the stabilization of a costly stabilizing system
• Compatible with all cameras with a standard tripod thread
• Replaces a tripod or monopod
• Heavy-duty cable
• Small and light enough to fit right in your pocket

Related Questions and Answers

Q: 1. Are the GEN 1 FPV drone batteries supported by the fast charging?

A: Yes. With optional DJI Power SDC charging cables, you can use the SDC port on the Power 1000 to fast-charge various DJI drone batteries. Mavic 3: Go from 10% to 95% charge in approximately 32 minutes Air 3: Go from 10% to 95% charge in approximately 30 minutes Inspire 3 (TB51): Go from 10% to 95% charge in approximately 28 minutes Matrice 30 (TB30): Go from 10% to 95% charge in approximately 32 minutes

Q: 2. How long would this device last if I had TWO Nanlite PavoTube 30C RGB LED Tube Lights (4') plugged in?

A: I wanted to compare the results with the Explorer 1000 in a test I used for the Explorer 300. I had wanted to test the battery life of the Explorer 300 in a photography setting, so I attached the powerful 150W Godox SL-150 II video spotlight to it and turned the spotlight on to 100% output. I started with a 100% charge on the Explorer 300 at 8:57 AM, and monitored it throughout the day. I got roughly 5.5 hours out of powering the light with the Explorer 300. I ran the same test with the Explorer 1000, starting the test at 7:38 PM with a 100% charge. The light showed a draw of 57W. At 8:48 PM the draw showed at 59W and the state of charge was 92%. At 5:27 AM the draw was 58W and the state of charge was 33%. I had to leave for my work day by about 8:30 AM, and didn’t return home until about 5 PM, at which time the battery was 100% drained. Based on the math from these data points, I would expect that I could get between 14 and 15 hours of straight powering of the light…depending on how accurate the power meter on the front of the unit is.

Q: 3. Hi Do you have this in AU plug? Thanks!

A: No it has a USA/North American AC wall connector.

Q: 4. I want to know if I can use it with Aputure 600d pro ? Thank you

A: The Aputure 600D supports power from a generator or wall outlet.

Q: 5. Is the display switchable between °F and °C?

A: Yes, the CineStill Film °Cs Temperature Control System TCS-1000 can switch between F and C readings.

Q: 6. Is this cage tripod mountable?

A: Yes, on the bottom you will find the standard tripod mounting holes.

Q: 7. What size drill bit is recommended to install the plates?

A: According to the manufacturer, you may use a 3/32nd-inch (2.35 mm) size wood drill bit to install the Impact MBM-1000 Magnetic Background Mount System.

Q: 8. Is the A/C power output in the form of a pure sine wave or a modified sine wave?

A: According to the manufacturer, the DJI Power 1000 Portable Power Station outputs AC power as a pure sine wave.

Q: 9. Does this cool as well as heat to the set temp (doesn’t rely on ambient temp for cooling) ??

A: This is only a heater and a circulator.

Q: 10. Can longer 15mm rods be added or used with this mount?

A: The rods on this system are permanently attached and are not removable.