The AA200PHD-CE 6-Input 200W CE-Listed Mixer Amplifier from Atlas Sound is a 6-input channel mixer amplifier designed for distributed business paging and background music (BGM) systems, medium-to-large speech privacy systems, and in applications where music on hold (MOH) and paging is required. With four microphone/line input and two stereo line inputs, the AA200PHD-CE Amp can accommodate a variety of input sources including paging microphones, media players, and digital music receivers. The AA200PHD-CE operates on 220-240 VAC for the European market.

The AA200PHD-CE Amp includes an automatic system test, the Push Here Diagnostic (PHD). The PHD button is designed to check the connected speaker lines for wiring and impedance errors. This test can be activated once all speakers are connected and the circuit automatically verifies that the attached speakers' tap settings do not exceed the amplifier's rated power, no speakers are mistakenly tapped at 8 ohms, and the speaker wire is free from shorts.

The amp also incorporates a Remote Input Selection and Remote Level Control feature that allows the integrator to use the WPD-RISRL remote wall plate (not included), which lets the user select the input and adjust the volume from that wall plate up to 200’ from the amplifier.

The AA200PHD-CE Amp provides 200W output power into 25/70.7V, or 4-ohm speaker systems. A rear-panel DIP switch allows for creation of Zone 2 output mix using any or all of inputs 1-4. Unit can also be set up to mute Inputs 2 through 6 on signal from Input 1 for paging applications where other input sources need to be muted during a page. Inputs 1 to 4 are either Mic or Line input selectable and phantom power is an option when using them as a microphone input.

6-Input Mixer/Amplifier for Installs    Voltage Compatibility: 220-240 VAC    200W into 25V/70.7V and 4-Ohm Loads    4 Balanced Mic/Line/Tel Inputs    Push Here Diagnostic (PHD)

Voltage compatibility: 220-240 VAC (Europe)

200W into 25/70.7V and 4-ohm loads

Automated diagnostic system test (Push Here Diagnostic)

Four balanced Mic/Line/Tel inputs with phantom power

Three unbalanced, summing line-level inputs

Input assignable zone 2 output

Remote Level Control

Remote Input Select (RIS)

Line output

Preamp In for external processors

Variable mute sensitivity control for Input 1

Contact closure mute terminals

Rear-mounted DIP switch allows mute receive for inputs 2 through 6

Related Questions and Answers

Q: 1. What kind of bulbs to use for this product?

A: The most common bulbs are BTL and BTN. They are 500 & 750 watt bulbs. 750W is the highest wattage you can use. There are more uncommon bulbs that will fit as well, such as 565w or 600w.

Q: 2. Is there a warranty?

A: This product has a one year, limited manufacturer's warranty.

Q: 3. if i connect 4 mics, can it allow 2 mics to be 'on' at the same time? (i.e. 2 different talkers), or the 'MaxBus' will strictly limit it to 1 mic at a time only?

A: The Shure SCM410 allows you to connect and use up to four microphones at the same time.

Q: 4. My mics need 48v phantom power. I dont see that in the specs? Can it supply or not?

A: I use this mixer with an Audio Technica condensor mic. The mic's specs say it requires 48 volt phantom power, but it works fine on the 12 volts from this mixer. I even got an external 48 volt phantom power supply, thinking the mic would sound even better with the full 48V, but it sounds the same with 12 or 48 volts.

Q: 5. Just received the CAME-TV CE-1500WS LED Video Spotlight and the fan seems to be on permanently after pushing the fan button on and off. Also heard a pop an a little burning smell that went away. Everything still seems to work after hearing the pop?

A: I apologize, but this type of inquiry cannot be taken care of through this feature of our website. Please contact our Customer Service department by entering Live Chat, emailing directly to cs@a href= http://bhphoto.com, target= _blank bhphoto.com,/a or calling us toll-free at 800.221.5743.

Q: 6. Is the ballast necessary for this lamp to be used? https://a href= http://www.bhphotovideo.com/c/product/664968-REG/Arri_518500_M18_HMI_Lamphead_110_220VAC.html target= _blank www.bhphotovideo.com/c/product/664968-REG/Arri_518500_M18_HMI_Lamphead_110_220VAC.html/a

A: Yes a ballast is needed to power the Arri M18 HMI Lamphead. The recommended ballast would be the Arri 1200/1800W High Speed Electronic Ballast B&H # ARBE1.21.8K. Please see the image for reference.

Q: 7. Is the adapter for 220 volts just for the plug or do you need a different adapter for the 220 volt bulb?

A: The power cable and switch for this unit suits both 120v or 220-240v no adaptor required. Therefore you can place any voltage lamp that fits the base of this unit. Obviously the lamp voltage should match the voltage of the country or region where you are using this light.

Q: 8. Is this amp (TOA A-2240) rack mountable? If so, what is the product number for brackets?

A: There is not a rack kit available, but you could use a rack shelf.

Q: 9. Is it possible to disable the 12v phantom power?

A: Yes. There are 4 numbered DIP switches on the back of the unit. To disengage the phantom power, simply flip the right-most switch numbered "4" into the down position, and the phantom power will turn off.

Q: 10. Will the mixer automatically set the microphone sensitivity? And does it have a limiter?

A: You will have to initially set the mic levels. Then it will open the mic when someone speaks. Yes it has a limiter. A Multi-pin Logic connection provides Mute, Gate and Override remote control options.