Use this compact Passive 1 x 2 Triple-Rate Splitter from Apantac to split one 3G/HD/SD-SDI, CVBS, or ASI input signal to two BNC outputs. It supports a pass-through of up to 16 channels of embedded audio. The signal can reach up to 330' end to end. No power is required to utilize the splitter.

Split 1 x BNC Input to 2 x BNC Outputs    Signal Reaches up to 330'    Compatible with 3G/HD/SD-SDI, CVBS, ASI    Compact Design, No Power Required

Related Questions and Answers

Q: 1. have you got multiviewer with analog audio input , and analog video input with other features of MI 16?

A: This is the closest we match we can offer : Gra-Vue VIO MVS-16HD-D 1U Multiviewer B&H # GRVIOMVS16HD

Q: 2. Would this cable allow me to send and record 4k raw from a Canon c300 mark II to an Atomos Shogun?

A: Yes. 3G-SDI is 10-bit 4:2:2 4K at up to 30p 12G-sdi is good for 4Kp60 resolution and higher bit rate, so it is also compatible with previous standards like HD/3G-SDI.

Q: 3. Hi,Can it sacle and crop from 1080i 16:9 to full screen 1024x768 4:3 (croping both sides)?

A: Yes.

Q: 4. Can it convert a DVI input to HD-SDI using a DVI to HDMI Cable?

A: If you are converting a DVI-D to HDMI, then yes that should be no problem. You will have to also factor in audio. your DVI to HDMI conversion will need to embed the the audio into the HDMI stream.

Q: 5. Can I set up dac-70 SDI output to atem television Hd and HDMI out put to projector ? Anyone try before please help me .

A: Yes that is possible.

Q: 6. Is it the St type connector for fiber

A: Yes, it is an ST/PC connection.

Q: 7. what is the length when coiled and just sitting on a table? And then how far out does it stretched out?

A: The 10 inch coiled cord extends up to an additional 12 inches.

Q: 8. Eternally grateful for your input... If input VGA at 1024x768 and it is set to output at 1080, will I see pillar boxes and a slight letterbox at the top since it is outputting 1:1 or will it fit to the vertical height? How about for 720? Thanks!!! Steve

A: We are using it similar to what you are describing. If you put VGA in and set output to 1080 it will be full screen. As far as 720, we have not used it yet.Lenny

Q: 9. How does this SDI splitter operate without a power supply? It seems like all the other units like it require one.

A: According to Apantac, this passive splitter has minimal internal wiring, and draws power through the SDI connection.

Q: 10. Has anyone used this to input HDMI from PC to an SDI input , on the BMD 1 M/E Switcher? We tried using a Decimator MD-HX and have not had any luck.Thanks!

A: 1st, your Payload: BMD ATEM by default is 1080i / 59.94; Delivery: SMPTE Level B. Your Decimator MD-HX, those are configured by default as Output Converters. Install the Decimator control Panel to configure (Decimator)as an Input Converter. It will do what you want.The DAC-70s are SMPTE Level A. At 1080i / 59.94, they will work as long as the Payload remains 1080i / 59.94. Delivery: SMPTE Level A or B, does not matter at that rate. We use both DAC-70's & Decimators, among other Converters, with our BMD ATEM 2 M/E Production Studio 4K Video Switch. Hope that helps!