The Lectrosonics VRT2 Receiver Module supports 3080 tunable frequencies across a 77 MHz bandwidth (three standard Lectrosonics blocks), matching the tuning ranges of the SSM, LT, and LMb "large bandwidth" transmitters. Up to six modules can be used simultaneously when installed in the Lectrosonics 1 RU Venue2 receiver main frame (available separately), and utilized in wireless applications for live stage, theater, houses of worship, and more.

The VRT2 module feature IQ dynamic-tracking filters, which accommodates a wide range of transmitter-RF power levels while also enabling tight channel spacing—critical features as the RF spectrum continues to shrink. Furthermore, the receiver modules can be operated independently, each with switched diversity reception for a total of six audio channels or operated in pairs for a more robust diversity reception with one audio channel per module pair.

Finally, the VRT2 modules are easy to change with no tools required and can be mixed and matched within one frame in any position, except when paired for ratio-diversity reception. VRT2 modules are not compatible with older Venue (VRM, VRMWB, and VRMWBL) frames.

For Venue2 Rack Frame    3080 Frequencies, 77 MHz Bandwidth    Channels 21, 22, and 23    Tracking Front-End Filter

When the incoming RF signal is strong, the iQ filter switches to a narrow-band mode with reduced gain for additional suppression of signals above and below the operating frequency. When the incoming RF signal level weakens, the filter switches to an extended-range mode for maximum sensitivity in the receiver module

The receiver modules interface with the main assembly through multi-pin connectors on either side of the chassis

Related Questions and Answers

Q: 1. Is IFBT4 block 19 compatible with the A1 receiver, will the frequencies match up?

A: Yes, the Lectrosonics IFBR1B Bodypack IFB Receiver with Charger (A1: 470 to 537 MHz) is compatible for use with the Lectrosonics IFBT4 Frequency-Agile IFB Transmitter (Frequency Block 19), which covers 486.400 - 511.900 MHz (B&H # LEIFBT419). It can also be used with the Lectrosonics IFBT4 Frequency-Agile Compact IFB Transmitter (Block 470), which covers 470.100 - 495.600 MHz (B&H # LEIFBT4470), and the Lectrosonics IFBT4 Frequency-Agile IFB Transmitter (Frequency Block 20), which covers 512.000 - 537.500 MHz (B&H # LEIFBT420).

Q: 2. Where can I find a holder for my Sony camera for this receiver?

A: https://www.bhphotovideo.com/c/product/1095137-REG/lectrosonics_lrshoe_receiver_mount_kit.html/overview?sts=pi&pim=Y

Q: 3. Is this compatible with the plug on HMa transmitter?

A: Yes, the Lectrosonics IFBR1B Bodypack IFB Receiver with Charger can receive signal from a Lectrosonics HMa transmitter on the same frequency range set to IFB Mode.

Q: 4. Can I buy additional receiver to pair up and have a total connections of 3 receivers to 1 transmitter?

A: Yes. multiple receivers may be used with a single transmitter. Frequency Presets There are 10 presets available for programming in the IFBR1B. The stored frequencies remain in memory during power OFF and even with the battery removed. Use the UP and DOWN arrows to scroll through the previously selected frequencies stored in the IFBR1B and quickly change frequencies for quick communication.

Q: 5. Will you be able to both record onto the onboard micro SD card, while transmitting the audio to a receiver at the same time?

A: The Lectrosonics DBSMD will transmit OR record. Not both at the same time.

Q: 6. Can I run this directly into a Canon C70s Mini XLR channel 1 and channel 2 inputs? If so, what cable do I need to do this?

A: Yes, when the outputs of the Lectrosonics DCR822 Compact Dual-Channel Digital Wireless Receiver are configured for analog output, they are compatible for connecting and sending signal to the audio inputs on the Canon EOS C70 Cinema Camera. A set of cables such as the Cable Techniques Low-Profile Straight TA3F to TA3M Mini XLR Cables (15", Pair) (BH #CACTVMXRTS15) would be appropriate for this function: https://bhpho.to/3sXaxjF

Q: 7. Is this receiver compatible with the Lectrosonics WM transmitter?

A: Yes. Just select the band that covers the block that the WM is in. A1 covers blocks 470, 19, and 20. B1 covers blocks 21, 22, and 23. C1 covers blocks 24,25, and 26.

Q: 8. Will this connect to my old UM200C transmitter?

A: No, this receiver is not compatible with the UM200C transmitter. The UM200C can be used with any 200 Series Lectrosonics receiver that operates within the same frequency group. The DCR822 receiver is compatible with D-Squared and Duet digital transmitters, including the DBu, DHu, DPr, DCHT, and M2T. There is backward compatibility with any Digital Hybrid wireless transmitters including the SM and SMWB series, WM, HM Series, MM400 Series, HHSeries, LT, LMb, UM400 Series, and SSM.

Q: 9. Is it compatible with Sennheiser G4 transmitter?

A: No it is not. Do not mix and match brands.

Q: 10. Does it come with the TA3 to XLR cable?

A: No