Marshall Code 50 Speaker Ohms

Audiosource Ad1002 2-channel Digital Power Amplifier

Product Code: ga31935
Availability: In Stock

$599.97 $887.96

Qty

0 reviews Write a review

Description
Reviews (0)

Power your home or commercial audio distribution system with the Audiosource AD1002 2-Channel Digital Power Amplifier. It has a 100W maximum stereo power output at 8 ohms, and a 150W maximum stereo power output at 4 ohms. It features treble, bass, and balance controls with stereo RCA inputs and binding post speaker outputs.

100W Max Stereo Power Output at 8 Ohms 4 Ohms and 8 Ohms Compatible Treble, Bass, and Balance Controls Stereo RCA Inputs Binding Post Speaker Connectors

Parameters
Power Rating	Stereo, 8 ohms: 50 W per channel, <1% THD+N Stereo, 4 ohms: 75 W per channel, <1% THD+N Bridged Mono, 8 ohms: 160 W, 1 kHz, <1% THD+N
Input Sensitivity	700 mV input for rated 50 W output into 8 ohms
Channel Separation @ 1 kHz	65 dB, referred to 50 W output into 8 ohms
Frequency Response	10 Hz to 30 kHz, -2 dB to 1 dB
Signal-to-Noise Ratio	100 dB below 50 W output into 8 ohms with 20 kHz Lowpass filter
Input Connections	2 x RCA stereo 1 x 1/8" (3.5 mm) 12 V trigger
Output Connectors	2 x Binding post sets 1 x 1/8" (3.5 mm) 12 V trigger
Controls Front Panel	1 x Power button 1 x A/B Speaker button pair 1 x Balance knob 1 x Volume knob
Controls (Rear)	1 x Bass adjustment 1 x Treble adjustment 1 x Mono select switch 1 x Auto on select switch
Sound Control Feature	Bass and Treble: ±12 dB @ 100 Hz and 10 kHz
Power Consumption	200 W maximum
Power Requirements	115 VAC
Dimensions	16.90 x 2.15 x 7.65" (43.00 x 5.50 x 19.40 cm)
Weight	4.7 lb (2.2 kg)
Packaging Info
Package Weight	5.85 lb
Box Dimensions (LxWxH)	20.2 x 9.7 x 4.3"

Main/Interrupt priority input switching

Main auxiliary output

Speaker A/B switching

Front panel balance and volume controls

Signal sensing "Power On" and Trigger Mode

Rear mounted treble and bass controls

Related Questions and Answers

Q: 1. Would this amp work with PVI 10 (Peavey) speakers (100 watts) along a Pioneer ddj controller? If is does...What accessories do I need in order to connect everything?

A: The Peavey PVI 10 speakers handle 100W peak power (not constant power) and 50W program power, so they handle less power than the amplifier puts out. You would need to be very careful to avoid damaging the speakers with too much power from the amp and keep the volume level low or use speakers that can handle more power like Mackie C200 Passive 10" 2-Way Loudspeaker (B&H # MAC200). The Peavey speakers have 1/4" inputs and the Pyle amp has SpeakOn output connectors so you could use cables like the Hosa Technology SKT-200 Series Speakon to 1/4" Male Phone Speaker Cable (12 Gauge) - 50' (B&H # HOSKT250Q). Please contact us if you would like further assistance with your setup. You may be better off using powered speakers instead of the amp and passive speakers.

Q: 2. How do you bridge the inputs so all 4 play the same sound ?

A: Bridge mode can be activated via a selector button on the back panel of the unit.

Q: 3. It works with 4 and 8 ohm. What about 6 ohm?

A: The Pyle Pro PTA1000 is able to run at either 4 ohms or 8 ohms, but not 6 ohms.

Q: 4. What should I have the gain at?

A: I have mine running a eurolive vp 1220, pa speaker, with a xenyx 802 board. It is only using channel a and i have it set to +10. It is only in being used an averaged sized room so it doesn't need to go any higher than that. I would say as long as it is not clipping you should be OK. I would run whatever you will typically play through it, find where it starts to clip and then back it down to where it stops. That would be a good max setting in my opinion. Also, check the user manual for your speakers for limits. You definitely don't want to blow them. I hope this helps.

Q: 5. I have a Klipsch KD-51M Bookshelf speakers & eventually will get a subwoofer. I want to connect to my computer. Will this work?

A: Yes, the Pyle Pro PTA1000 Professional Stereo Power Amplifier (250W/Channel @ 8 Ohms) (BH # PYPTA1000) will comfortably drive the Klipsch KD-51M bookshelf speakers. This amplifier will connect to your computer's analog audio output There is no subwoofer output on this amplifier.

Q: 6. Can you supply this with power input of 240VAC 50Hz?

A: At this time we only carry the 120v version. You could use a step down transformer with it, such as BH #SEST1500UD.

Q: 7. how to bridge 4 speakers at 8 ohms?

A: I'm afraid I had to call the manufacturer in Canada - Alas now days weno longer have the luxury of manuals inside the box with the amp .I also have 4 speakers bridged at 8ohms but cannot remember theconfiguration with the connecting blocks.Once you get this set up you will be well pleased - This Is A terrific power amp - 10 stars PC LA

Q: 8. how do you rack mount this amp?

A: Use a rack shelf.

Q: 9. Will this amp work with Bose Virtually Invisible 191 Speakers? Some list this speaker at 6 ohm's. The spec for this amp list 4 or 8 ohm's not 6.

A: Yes, this would be compatible. Bose lists the specs of the Virtually Invisible 191 speakers as 100w @ 8 ohms, but this amplifier would be compatible with speaker that are 4 - 8 ohms.

Q: 10. Can you connect this to home audio receiver?

A: Not from the speaker outputs on the home audio receiver. Only if it has pre-outs available for that. A lot of models only have pre-outs for use with powered subwoofers.

There are no reviews for this product.