Motorized Swing Down Ceiling Mount Tv Mounting Bracket

Nebtek Duo Monitor Bracket With 2.1mm V-mount Adapter

Product Code: ga32013
Availability: In Stock

$1,527.00 $2,336.31

Qty

11 reviews Write a review

Description
Reviews (11)

The Duo Monitor Bracket with 2.1mm V-Mount Adapter from Nebtek is compatible with the Blackmagic SmartView Duo & Nebtek NEB70HD Dual Monitor. The rear of the bracket has mounting holes for the included 2.1mm V-Mount battery adapter, as well as four 1/4"-20 threaded mounting holes for other gear, such as wireless receivers.

The bracket rests on the yoke and can be lifted on and off easily. It can be secured onto the yoke by tightening the knob and lever on the sides. The entire bracket is mountable to a 5/8" Baby Pin and allows for 360° rotation with pan and tilt. The rear bracket and handles offer protection against bumps and drops.

Key Specs
Mounting	Stand Mount: 1x 5/8" Receiver Accessory Mount: 4x 1/4"-20 Female Thread
Mounting
Mounting	Stand Mount: 1x 5/8" Receiver Accessory Mount: 4x 1/4"-20 Female Thread
General
Battery Plate Type	1x V-Mount
Power I/O	1x Barrel 2.1 mm Output
Materials	Aluminum, Steel
Dimensions	21.5 x 10 x 4.6" / 54.6 x 25.4 x 11.7 cm
Weight	6 lb / 2.7 kg

Powder coated steel alloy for yoke

Lightweight aluminum for bracket and handles

360° Rotation with pan and tilt

Handles for portability

Cradle-style yoke is mountable to 5/8" Baby Pin and allows for easy removal

Related Questions and Answers

Q: 1. will this work with Arri Artemis 2?

A: The Nebtek 3-Pin Fischer Male to Female D-Tap Cable (24") can connect to the 12V 3 amp Fischer 3-pin on the ARRI ARTEMIS 2 with 1.8" Standard Post (Basic Set).

Q: 2. this item is compatible with shogun inferno 7" monitor?

A: Since the Nebtek Power Bracket with Battery Adapter for Video Devices PIX-E7 Recording Monitor (Anton Bauer) is a special order product and not one that we have on hand we can not test it with the Shogun Inferno 7", and cannot say for sure if they would be compatible. Since the Power Bracket is specifically designed to work with the PIX-E7 I think it is unlikely that it would be compatible with he Inferno.

Q: 3. Is there a C-Stand mount on bracket?

A: No, there isn't a C-stand mount on the bracket.

Q: 4. If the sub sits on the floor while the speakers are mounted to the wall bracket, what connects the speakers to the sub?

A: Your PRX ONE subwoofer would be connected to the main speaker array with a SpeakOn cable, as pictured in the manual on page 32: https://www.bhphotovideo.com/lit_files/743690.pdf

Q: 5. Can I easily flip the monitor 90 degrees from horizontal to vertical?

A: Yes you can easily flip your monitor 90 degrees from horizontal to vertical.

Q: 6. Does this allow for a Teradek Receiver between the Battery Plate and the Monitor Cage?

A: That will all depend on the exact Receiver being used, but yes this product does come with a Spacer that will make it possible. Here is a photo that demonstrates the space available. https://bhpho.to/2O1gx5F

Q: 7. Is there any instructions for how to use this Adapter Plate?

A: I can help you through the process. The smaller 100mm hole pattern attaches to the existing mounting bracket with bolts provided. The larger hole pattern then attaches to the 200mm VESA on the back of the monitor with bolts provided. Feel free to contact us at msegrip.com for further assistance.

Q: 8. Will this work with the SmallRig Monitor Cage with Sun Hood for SmallHD 702 Touch?

A: The SmallHD V-Mount Battery Bracket Kit for 702 OLED Monitor is listed to work only with the 701 Lite, 702 Lite, 702 Bright, or 703 Ultra Bright.

Q: 9. Can this be used with the F-5A?

A: TV-Logic does not have a gold mount option for the F-5A display. Your could use this cable - TVLogic D-Tap to Mini-XLR Coiled Power Cable for VFM Monitors (29") BH #TVDTAPC or this plate from Bebob - bebob Monitor Battery Plate for TVLogic 058W, F5, F-7H & F-7H MKII (Gold Mount) BH #BEAMMICROTVL

Q: 10. Can you tell me the width inside and outside the "fork"? Want to use on different brand arm I already own. Tks!

A: These dimensions for the K&M 23881 5/8" Adapter for Monitor Mount Arms, BH # KMAMMB, are not published by the manufacturer. The outside is about 2.1" and the inside is just less than 2".

David	24/09/2024
I needed an articulating VESA style mount for my Osee LCM156-A production monitor. All the other products I found were much more expensive. I was concerned that this would not fully support the weight of the monitor which ships with an attached carry case/sun hood (approximately 14 pounds), but I thought I'd roll the dice and see if this would support it...and it does. The unit is small enough that I can pack it into the carry case without having to remove it (a HUGE plus), and it provides adequate angle adjustment range. The plastic ratchet handle may wear out over time, but I know this can be replaced with a solid metal one. For the cost of this product, the plastic handle isn't a surprise. The more important hardware is the bit that clamps onto the articulating balls. That hardware is all metal, and looks like it will last with proper use. The supplied screws are a bit too long and bottom out before tightening. I was able to shimmed the plate with 2 washes at each screw, and it appears to hold well. Overall, I'm very pleased with this mount, and think it's a good value. 5

Ranald	19/09/2024
This is such a well-made, well-designed, well-fit for function item that the low price is a surprise. Does exactly what it is supposed to do and does it well. If you think you need this functionality, then buy this one. 5

Brian	07/08/2024
I used this for the food stylist monitor, and it worked just fine. At first I was concerned about the long handle because it would hit the back of my monitor as I tightened it. I quickly realized the handle can be pulled out and readjusted so you can continue tightening. The double joint was useful to get the right viewing angle and enabled the monitor to not hit the post it was mounted to. 5

Marc	07/07/2024
Solid material and very sturdy. Great product. 5

Channel70	21/06/2024
A fast and inexpensive way to mount monitors. Highly recommend. 5

Huntly	15/06/2024
NOTE: Make sure you have M4 screws in your bag! This doesn't come with them and you'll need 4 to mount your monitor. I've used this with my 27 Dell monitor and a 32 smart TV, held up great in both cases. Super east for events to be able to mount your monitors off baby stands. 5

Matt	11/05/2024
Functional! I have VESA mounted monitor on the adapter. Setup was easy. The tightening handle is cleverly designed. It allows for adjustment by pulling out the handle turning to a better tightening position and then rein gauging the handle and tighten. The clamping mechanizum is holding a 7 lb. monitor no problem. The adapter does not thread on the mic stand. It sets over the top of the mic stand and then is tightened with thumb screen. Screws are included for mounting the adapter to the monitor. Just what I was looking for. HAPPY! 5

Richard	05/05/2024
I initially bought this mount for some DIT work so I could mount my monitor on stands in front of my cart so they didn't take up desk space but ever since I bought them they've been helpful for so much more. For instance instead of almost renting a SmallHD production monitor for a client monitor I was able to just use my Acer monitor on the stand and looked the same if not better to the client. The only complaint I'd have is that the mount does slowly drop down a bit with my monitors but the 2 that I have are heavier than most monitors so this isn't a huge deal at all. I would highly recommend this mount over almost all of the other vesa stand mounts that easily cost 4x more. 5

Riza	23/04/2024
After trying DIY way with the VESA mount which never works well, finally using this easy to install mount adapter makes it work. The build quality also very good. 5