Mount an accessory onto your rig with the Accessory Mount with 1/4"-20 Thread and 15mm Rod Clamp from GyroVu. The durable aluminum mount features a single, standard 15mm rod clamp and a 1/4"-20 mounting thread. It secures on a separately available 15mm rod using a locking lever and can support an accessory that weighs up to 3 lb.

1/4"-20 Mounting Thread    Single 15mm Rod Clamp    Locking Lever, 3 lb Load Capacity    Durable Aluminum Construction

Related Questions and Answers

Q: 1. Can I use this to mount a Kondor Blue d-tap hub splitter onto a 15mm rod?

A: No, the Kondor Blue 15mm Rod Clamp to Accessory Mount (Space Gray) would not connect to the Kondor Blue Male D-Tap to 4-Port Female D-Tap Splitter Hub. One solution would be a Magic Arm. BH #KOKBMGCARMBK and replacing one of the ends with a 15mm BH #KOB15BALL. Many customers also work with this NATO clamp to attach it to a NATO Rail on their cage or rig. Kondor Blue Anti-Twist NATO Clamp (Space Gray) BH #KOKBNATOCAT. You could also work with the following Wooden Camera Universal 15mm Rod Clamp (1/4"-20) BH #WOA00131

Q: 2. RT Receiver Rail Clamp for 15/19mm rods fits 1/4-20 will it work with the Teradek Bolt 6 LT 750 3G-SDI/HDMI Transmitter?

A: Yes, the Teradek RT Receiver 19/15mm Rod Clamp with 1/4"-20 Mount will mount to the bottom of the Teradek Bolt 6 LT 750 3G-SDI/HDMI Transmitter.

Q: 3. How many locating pin holes are there?

A: The Wooden Camera ARRI Accessory Mount to 15mm Rod Clamp Adapter has 4 threaded holes that you can screw ARRI locating pins into on the bottom.

Q: 4. What is the weight capacity? Can it handle a magic arm with an Atomos 7" Ninja Inferno and two np-f750 batteries?

A: Niceyrig does not list a weight capacity however I would not recommend using this for a Ninja Inferno. The weight of that monitor with batteries on it may cause the clamp to slip. This product is best suited for smaller lighter weight products such as video transmitters, and microphone receivers.

Q: 5. Can this screw into the top mounting points on the body of a FX-6 without a cage? In other words, is the thread reach compatible as not to damage the body when tightened?

A: The SmallRig Single 15mm Rod Clamp with 1/4"-20 Thumbscrew will be able to mount to and make a solid connection with the 1/4"-20 receivers on top of the FX6.

Q: 6. which material is make whole plate ?

A: This product is a combination of ABS Plastic and Aluminum.

Q: 7. Canon XF605 camcorder: Can this unit be powered off a D-Tap V=lock battery? If so is there a cane with the correct plug connectors?

A: Yes. The following is needed in order to do so. GyroVu D-Tap to Canon BP-828 Dummy Battery Cable (30") BH #GYVDTAPBP828 • MFR #GV-DTAP-BP828 https://bhpho.to/3PSrt4J and v-mount battery of choice.

Q: 8. Does the M4 screw fit into the 1/4-20 screw holes?

A: An M4 Screw and a 1/4"-20 threading are not compatible.

Q: 9. Can you remove the screw that holds the thumbscrew, leaving another threaded 1/4"-20 hole on the clamp, or is the screw permanently attached to the clamp?

A: The thumbscrew is required to tighten the rod clamp on the 15mm rod. In addition to that the screw for holding the thumbscrew is smaller than a 1/4 20

Q: 10. Can you charge the battery using this plate?

A: This plate is not for charging the battery. We do have a simple battery charger, B&H SKU#IKC1K