The FotodioX WonderPana 8.0" Holder Bracket is a two-piece assembly designed to be used in combination with a FotodioX WonderPana FreeArc XL Core Unit or a WonderPana XL Aluminum Step-Up Ring. Attaching the WonderPana 8.0" Holder Bracket to a WonderPana FreeArc XL Core Unit or a WonderPana XL Aluminum Step-Up Ring can allow for the convenient use of two 2.0mm-thick filters measuring 7.9" wide, or one 2.0mm-thick filter measuring 7.9" wide along with one FotodioX 186mm round filter behind it.

Use of this holder bracket is easily accomplished by separately attaching its two assembly pieces to opposite sides of a WonderPana FreeArc XL Core Unit or a WonderPana XL Aluminum Step-Up Ring using six of the eight included brass short-screws. Pre-tapped threaded inserts along the edge of a WonderPana XL Aluminum Step-Up Ring accommodate those screws and ensure correct positioning of the two assembly pieces so that they are positioned parallel to each other and can hold a 7.9"-wide filter between them. The combined WonderPana XL Aluminum Step-Up Ring, and WonderPana 8.0" Holder Bracket can then be attached to a compatible lens.

For WonderPana FreeArc XL Core Units that consist of a rear lens collar and a front filter holder, pre-tapped threaded inserts along the edge of the front filter holder accommodate six of the eight brass short-screws for correct positioning of the WonderPana 8.0" Holder Bracket's two assembly pieces. Once the holder bracket and a front filter holder are combined, and the separate collar has been slid over the rear of a compatible lens until it has achieved a secure fit, the front filter holder with the attached holder bracket can be screwed onto the front of the installed rear lens collar.

After being fitted onto a compatible lens, the bearing design of the WonderPana FreeArc XL Core Unit allows a WonderPana 8.0" Holder Bracket to be rotated 360°. This permits the use of graduated neutral density and other filters that are enhanced by varied positioning.

The FotodioX WonderPana 8.0" Holder Bracket provides two pairs of filter slots, a configuration that accommodates two compatible rectangular filters. For each rectangular filter that is placed within one of the holder bracket's slots, its position is secured by integrated guides within each slot. These guides apply pressure along both sides of a filter that is sufficient to hold it in place, but permits movement of that filter. This can complement the use of graduated filters whose effect can be adjusted to better suit changing lighting conditions or creative demands by sliding them up or down within a filter slot.

The WonderPana 8.0" Holder Bracket features a lightweight, aluminum-alloy construction that has a corrosion-resistant, black anodized finish for durability. A rigid pouch is included for storage and transport.

For Lens with 77mm Front Filter Threads    WonderPana 8.0" Holder Bracket    Use with WonderPana XL Step-Up Ring    Use with WonderPana FreeArc XL Core Unit    Rotates 360° with FreeArc XL Systems    77mm-186mm XL Step-Up Ring    Compatible with 8.0" Holder Bracket    Compatible with FotodioX 186mm Filters    186mm Center-Pinch Snap-On Lens Cap

• When used with a FotodioX WonderPana FreeArc XL Core Unit or a WonderPana XL Aluminum Step-Up Ring, allows for the convenient use of two filters measuring 7.9" wide, or one filter measuring 7.9" wide along with one FotodioX 186mm round filter installed on a WonderPana FreeArc XL Core Unit or WonderPana XL Aluminum Step-Up Ring
• Provides two pairs of filter slots, a configuration that accommodates up to two 2.0mm-thick rectangular filters
• Allows up to two compatible rectangular filters to be rotated 360° when used with a FotodioX WonderPana FreeArc XL Core Unit
• Integrated guides within each filter slot apply pressure along both sides of a filter that is sufficient to hold it in place, but permits movement of that filter, complementing the use of graduated filters whose effect can be adjusted to better suit changing lighting conditions or creative demands by sliding them up or down within a filter slot
• Lightweight, aluminum-alloy construction with a corrosion-resistant, black anodized finish for durability
• Microfiber cleaning cloth included, plus a rigid pouch for storage and transport

Related Questions and Answers

Q: 1. will it fit Sony PXW-X70?

A: I have a Canon camera. If your Sony has a 62mm diameter lens, it'll fit. Have a look into the front of the lens at the writing and look for 62. If it has another number in front of the , that's the diameter you need. This lens cap grips my 62mm lens very well. I also fitted a Sensei Cap Keeper Lens Cap Holder to make sure I don't loose the lens cap. Good luck!

Q: 2. Does the filter holder or filters physically block any of the field of view of sigma 14-24 mm dg hsm f mount lense? Not dg dn

A: FotodioX WonderPana FreeArc XL Core Unit Kit for Sigma 14-24mm Art Lens with 8.0" Holder Bracket does not block any of the filed of view, also the filters don't block it either.

Q: 3. Does the filter holder or filters physically block any of the field of view of sigma 14-24 mm dg hsm f mount lense? Not dg "dn"

A: No, the FotodioX WonderPana FreeArc XL Core Unit Kit for Sigma 14-24mm Art Lens with 8.0" Holder Bracket would not physically block any of the field of view on a Sigma 14-24mm Art lens.

Q: 4. Does it fit Nikon AF-S NIKKOR 35mm f/1.8G ED Lens?

A: The cap will fit fine if you know the correct size of the lens. If 58mm matches, it should not be a problem.

Q: 5. Will this fit the Sigma 14-24 DG N sony e Mount?

A: Yes, if it is the Sigma DG DN Art lens.

Q: 6. I have a collection of various 82mm circular filters from ND & tint to circular polarizer that I use in conjunction with step down rings on various lens. Since the filters are 82mm may I assume I can use this lens cap over whichever filter may be windup on the front?

A: Wont be able to use a filter on this lens due to the front element.

Q: 7. Will this work on the new Sigma 12-24 Art?

A: It works well with the 11-24 canon so I can only assume that it will work with that lens. n Needs to be kept spotlessly clean so as to avoid flare abboration

Q: 8. Since front holder and rear collar when assembled block hood petal cutouts of 11-24mm lens, how bad is the vignetting?

A: The FotodioX WonderPana FreeArc XL Core Unit Kit for Canon 11-24mm Lens with 186mm Slim Circular Polarizer Filter will not vignette when mounted to the Canon 11-24mm Lens.

Q: 9. I am purchasing a 67-77 mm brass step up ring. Is this lens cap the right size?

A: No, you would want a 77mm lens cap.

Q: 10. Will this work as a replacement for my native RF 24-70mm lens cover?

A: Sensei 82mm Center Pinch Snap-On Lens Cap BH #SELC82 will work as replacement for the Canon RF 24-70mm f/2.8 L IS USM Lens BH #CA2470RF • MFR #3680C002.