StrikeIt1 will operate up to two (2) 24VDC panic hardware devices simultaneously. It is designed to handle the high current surge panic hardware locking devices demand. Each lock output has an adjustable relock delay timer. It will control a pair of doors simultaneously or independently control two individual doors. It has a follower relay for each output to trigger external relays, ADA push plate switches, etc. Delayed follower relays control automatic door operators for doors that are always locked or for doors that are unlocked during the business day. In addition, two un-switched auxiliary voltage outputs are provided for powering card readers, keypads, REX PIRs, electronic timers, relays, etc. A configurable FACP interface will either provide power or remove power to the lock outputs when activated. LED status indicators are provided to monitor AC power, FACP status and for lock output wiring supervision. Intelligent logic provides protection against accidental shorting of lock outputs.

Agency Listings

• UL Listed for Access Control Systems (UL294),
• CUL Listed - CSA Standard C22.2 No.205-M1983, Signal Equipment.
• File# BP6714.
• CSFM - California State Fire Marshal Approved.
• File# 3774-1335:114.
• MEA - NYC Department of Buildings Approved.

• Two (2) 24VDC individually or simultaneously controlled lock outputs rated @ 15 amp for 300ms.
• One (1) 12VDC filtered regulated auxiliary output rated @ .75 amp continuous supply current.(Not affected by FACP trigger)

• One (1) 24VDC filtered regulated auxiliary output rated @ .75 amp continuous supply current.(Not affected by FACP trigger)
• Two (2) delayed follower form "C" relay outputs rated @ 0.6 amp/28VDC. Delay time is selectable .5 seconds or 1 second.
• Energized duration is 1 second.
• Two (2) follower form "C" relay outputs rated @ 0.6 amp/28VDC.
• Relays energize while input is closed.
• Input 115VAC 50/60Hz, 6.3 amp.
• Two (2) N/O Trigger Inputs.
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when AC fails.
• Maximum charge current .3 amp.
• Green LED indicates input 115VAC present.
• Green LED indicates panic device status (short, open or triggered).
• Red LED indicates when FACP disconnect is triggered.

• Normally Closed FACP trigger input.

• LK1 and LK2 adjust the panic device release time for the lock outputs from 300ms to 30 sec.
• Lifetime Warranty.

• Accommodates up to two (2) 12VDC/7AH batteries.
• Dimensions: 13.5"H x 13"W x 3.25"D.
• 1/2" and 3/4" combination knockouts.

Related Questions and Answers

Q: 1. What is the connector to the X4 unit called?

A: It is a proprietary connector un-named by the manufacturer.

Q: 2. Where does it attach to on the Ronin M? Can it tilt horizontally as well as vertical?

A: I used the DJI monitor/accessory holder with the Ronin-M mobile device holder and I can place it anywhere along the top ba of the Ronin-M. Works great- yes you can rotate it vertically or horizontally. But you need a way to secure the mobile device holder on the Ronin-M. This set up works well.

Q: 3. Will this quickset plate fit the Arca Swiss Z1 ball head 801103?

A: Yes. But please keep in mind that the following adapts to smaller QR plates such as the following plates mentioned. 802255, 802260, 802262 and 802265.

Q: 4. Does this unit come in a NEMA 4 case?

A: There currently isn't an option for a NEMA 4 case with this unit, only the NEMA 1 indoor model.

Q: 5. Would this device hold my camera just as securely as the Fliplock or Classic with the screw devices?

A: This device can hold your camera just as securely as the Fliplock or Classic version of the clamp as long as you are using the SlideFix type plates for it.

Q: 6. Will this PTZ control a Roboshot 30E NDI camera?

A: Yes it will

Q: 7. Are the safety pin removable?

A: The pins are not removable by any normal means.

Q: 8. Does this work with an iphone 5, the power buttion is on the top, does the clamp push the power button?

A: Hello. You should be able to position the phone so that the power is not activated. Thanks.

Q: 9. how to install supporting software?

A: Hello, You need to load the CD that is given with the hand control. And then you may find the related file to proceed inside prompter software. Anycase, if you face a problem, then you may check the PDF file that you can find along with the hand controller. Please feel free to contact if you need further assistance. Thanks. Pınar.

Q: 10. will it work for MADI?

A: You will need to contact the manufacturer directly for this question. They can be reached at 718-567-8181.