Enjoy your audio with this pair of walnut Audioengine HDP6 2-Way Bookshelf Speakers. They can handle 10 to 150W of power per channel and are equipped with a 5.5" Kevlar woofer and a 1" silk dome tweeter. These speakers are wall- or ceiling-mountable via 1/4" threaded inserts on the rear and bottom panels.

10 to 150W per Channel Power Handling    2-Way Speaker Design    5.5" Kevlar Woofer    1" Silk Dome Tweeter    50 Hz to 22 kHz Frequency Range    0.75"-Thick MDF Cabinet

The slotted rear bass venting ports are designed to eliminate wave turbulence, transitioning the low-frequency energy from the speaker cabinet into your room.

HDP6 speakers include two standard 1/4" threaded inserts on the rear panel and another insert on the bottom of each HDP6 cabinet for attaching a speaker mount or bracket.

Audioengine uses ferrofluid-cooled silk dome tweeters with neodymium magnets. Silk tweeters are fashioned to hold up well under high power, and the edge-driven design provides a smooth response. The woofers are Kevlar-woven glass-aramid composite with rubber surrounds. Kevlar is strong, which means the woofer retains its shape when being driven at high levels. The HDP6 woofers are housed in cast-aluminum frames for enhanced rigidity and heat dispersion.

To minimize unwanted resonances and distortion, Audioengine uses 3/4"-thick MDF walls with internal bracing. Internal sound-damping material is used to reduce unwanted sound reflections inside the cabinet.

The HDP6 includes detachable grilles that are firmly held in place with hidden neodymium magnets for a clean look.

Both drivers are magnetically shielded to allow you to place the speakers within a few inches of a video monitor. This shielding also offers protection for hard-drive-based digital music players.

Related Questions and Answers

Q: 1. Which cable should I buy in order to connect them with a speaker wire to my receiver?

A: Hi Omri, you may use bare speaker wire or banana plugs. Thanks! ^Ron

Q: 2. Can this speaker be used with Sony cd changer model cdp-ce500?

A: They will not connect directly to the CD player. You will need an AV receiver.

Q: 3. Would the NAD C 316BEE V2 amplifier pair well with these speakers?

A: This ELAC pair will work nicely with your NAD C316BEE V2 integrated amplifier.

Q: 4. Is Yamaha R-N303D Network Stereo Receiver capable of bringing out the best from this pair of speakers?

A: These are very sensitive 6 ohm speakers. The Yamaha R-N303D, while an excellent receiver, is not designed for 6 ohms, and is less than ideal. It can power the speakers, but could conceivably be damaged at high volume.

Q: 5. Do these ideally need max 120 watt input PER speaker or 120 total?

A: The maximum recommended wattage is 120w per channel.

Q: 6. Can it be wall mounted?

A: Yes. 100 %. 6.2 way to go for wall mount. Put them on wall shelves or hang etc. Important point is the breather is on front.

Q: 7. Since these speakers come with a preamp, is it ok to connect a turntable that also has a preamp?

A: It would not be an issue to connect the Klipsch The Nines 2-Way Active Wireless Bookshelf Speakers (Walnut, Pair) BH #KLNINESWN with a turntable that has a pre-amp.

Q: 8. I ordered ELAC DEBUT B6.2. I have Sony STR-DH190, is there any pronblem with this matching?

A: No problem at all. These ELAC speakers are well matched to the Sony STR-DH190 Stereo Receiver.

Q: 9. Will these speakers work well as rear channel speakers with a system powered by a Yamaha RX-V485 receiver?

A: Yes they will very well as rear surround speakers.

Q: 10. These speakers must be paired with a receiver or i can connect them directly to my PC? Thanks.

A: They must be connected to a receiver or amplifier.