The ikan EC1 Beholder is a 3-axis handheld gimbal stabilizer for DSLR and mirrorless cameras weighing between 2 and 4.5 lb. The EC1 offers unlimited 360° rotation along the yaw, pitch, and roll axes, and features an advanced 32-bit controller and 12-bit encoder system. The gimbal employs an adaptive PID algorithm to deliver stable rotation.

The EC1 offers three follow modes plus an auto-inversion mode that allows for upside down operation. Auto-inversion lets you use the gimbal with dual-handle support systems like the ikan DGH. The EC1 also features a lock mode that sets the camera in a fixed position, and a point-and-lock mode that locks the position you hold the camera in for a few seconds. The EC1 also has an OLED display on the rear that confirms the selected mode of operation and provides battery life info.

The EC1 is designed with a quick release baseplate that allows for convenient camera attachment and tool-less balancing. It also has a 1/4"-20 threaded mounting hole on the handle for attaching accessories for advanced setups, and a 3/8"-16 threaded mounting hole on the bottom for mounting onto a tripod, monopod, and other support gear.

The EC1 runs on three supplied 18650 batteries that provide 8 to 10 hours of operating life when used continuously, and up to 20 hours when the gimbal is switched between shooting and standby modes throughout the day. These batteries are rechargeable from within the EC1 via an included micro-USB AC adapter, and can also be charged using optional chargers such as the ikan ICH-SC4.

360° Rotation Along All 3 Axes    32-Bit Controller and 12-Bit Encoder    Adaptive PID Algorithm    Supports Cameras between 2 and 4.5 lb    Three Follow Modes Plus Auto-Inversion    Lock Mode and Auto Point-and-Lock Mode    Quick Release Baseplate    OLED Display    3/8"-16 Tripod Mount Threaded Hole    1/4"-20 Accessory Mount Threaded Hole

The EC1 Beholder features three 360° rotating brushless motors that give you a limitless range of motion along all three axes: yaw, roll, and pitch.

Using a 32-bit controller with a 12-bit encoder, the EC1 uses an adaptive PID algorithm to produce a reliably efficient handheld stabilizer.

In Lock Mode, the Yaw, Pitch, and Roll axes work together to keep the camera fixed and pointed in one direction. The camera's position will stay the same no matter how you move the handle.

Quickly lock your camera into any position by manually pointing and holding it in any direction. After a few seconds, the camera will lock and hold its position until it is reset back to default.

The EC1 features 3 different follow modes. In yaw-axis follow mode, the EC1 will only follow your pan movements. In pitch and yaw-axis follow mode, the EC1 will follow your pan and

tilt movements. The 3-axis follow mode gives you full control, allowing you to pan, tilt, and roll.

Switch to inverted mode at any time by simply flipping the handle over the camera. Inverted mode can be operated in conjunction with any of the lock and follow modes.

A display screen located on the back of the handle conveniently provides you with information on the battery life and operating mode.

Featuring a newly designed quick release baseplate system, the EC1 is easy to balance without any tools.

The EC1 handle a 1/4"-20 threaded mounting hole for attaching accessories such as a light, microphone, or monitor for advanced setups; and a 3/8"-16 threaded mounting hole on the bottom of the handle for to mount the EC1 on a tripod, jib, or dual-handle support system such as the ikan DGH.

Related Questions and Answers

Q: 1. I cant mount my gimbal on a tripod because the diameter of the hole in it is bigger than the screws shoe. what can I do?

A: It's my understanding the screw mount on the bottom is for an external monitor mount. There are two smaller diameter holes on the shaft (around the toggle switch and usb ports) that will mount to a standard tripod. I just tried and my quick release plate fastened just fine.

Q: 2. Seen on a forum elsewhere that you would have to use your camera on autofocus? Is that true? I'd be using it with the Sony A7 sii with Canon lenses...

A: I believe what you read was that you would not be able to have your hand on the focus wheel while using this gimbal. That is actually true of pretty much any stabilizer, motorized or non-motorized. The reason is balance. You could use the auto focus or you can set your shots beforehand in manual. Gimbals like this are really not designed for constant use, they are designed to get you nice, gliding shots. If you seek any further guidance on Gimbal Stabilizers feel free to email us directly at provideo@bhphoto.com.

Q: 3. does it have a timelapse mode ?

A: Unfortunately Melwin, no, it does not.

Q: 4. Will this work with a Sony A99 + Zeiss Lens 24-70mm, total weight: 4.07 lb?

A: Eduardo, It should work. But, we don't have the exact model to test and confirm in-house.

Q: 5. Would a GH4 with 12-35mm weigh enough for this gimbal?

A: The combination of GH4 and 12-35mm lens will weigh 1.9 pounds, just shy of the required 2 pounds. We do not recommend that combination. You would want to look in to gimbals like the Ikan Beholder DS1 or Zhiyun-Tech Crane instead, both of which would be able to balance the weight of that camera/lens combo.

Q: 6. Will it work with a common 5D mark ii?

A: Yes, it works with my 5dMk4 and a 17-40mm lens. I found the 24-70 2.8 very close to not being usable. The weight makes you have to balance the camera at pretty much the extremes of the adjustments, and it may not be able to twist and turn in all directions. Works great with the 17-40 and the old nifty fifty plastic lens.

Q: 7. I have a canon g40 camcorder with a saramonic transmitter mounted on the hot shoe. My question is can I move the combination backward enough to get a good balance?

A: While we have not tested this combination, we feel there is enough room with the plates adjustment to allow your camera and mic transmitter to work.

Q: 8. Will this be suitable with a Sony A99 + Zeiss Lenses 24-70mm?

A: The EC1 Beholder is designed to work with DSLR cameras and has a load capacity up to 4.5 pounds. The A99 and 24-70mm will balance on this device, they should work well.

Q: 9. Could this work with an NX1 + Sigma 18-35mm f1.8 lens?

A: I just used a sony A7sII with a canon 50mm 1.4 and a Metabones adapter. So, have no sure, but I think that probably it will work fine.You just have to find a balance and calculate the weight of the gear before.Sorry to don't have more informations

Q: 10. Will it work with Sony a6300 with 18-50mm Lenses?

A: It might, I don't have that exact combination to test in house. As long as the lens is heavy enough, it should work.