This aluminum EyLight Body is the fixture unit which holds the bulb and battery for the EyLight lamp system. A protective front cap is included. This unit is compatible with the separately available EyLight 5000K and 3000K LED bulbs and the 20W quartz-tungsten bulbs. Use this fixture to expand your existing EyLight setup if you already have extra bulbs, batteries, and mounting accessories.

1 x Eylight Fixture with Battery    1 x 5000K Bulb    1 x Charger, 1 x Adapter Stud    1 x Stud to Shoe Mount Adapter    1 x Light Stand (7')    1 x Gooseneck System

Related Questions and Answers

Q: 1. Will this lamp work in a fixture with a magnetic ballast and a hold to start switch?

A: The MyStudio 18" 5000K 15W "Daylight" Fluorescent Bulb for MyStudio Kits is for MyStudio system 20 and system 32 fixtures.

Q: 2. How many in a case?

A: Unfortunately, these are only sold singly and not in a case.

Q: 3. need to replace lost bolt that holds riser in desired place for frezzi 7' FHMS Heavy Duty Mini Light Stand?

A: We do not carry that part for the Frezzi stand.You will need to contact the manufacture directly, http://bit.ly/1GKhMKy.

Q: 4. What is the warranty for this?

A: This Frezzi FLC-4AP Quad Fast Simultaneous Charger with Power Supply (Gold Mount) BH #FRFLC4AP • MFR #93945 would have a 1 year manufacturers warranty.

Q: 5. Is this good for elinchrom mono light?

A: This stand would be fine for holding an Elinchrom monolight lower to the ground.

Q: 6. Will this support a Canon 1D MK4 with a 70-200mm lens?

A: That setup can support no more than 6.6 lbs.If you mean the canon 5d Mark IV and lens it is about 5.28 lbs combined. It is too close to the maximum in my opinion and at the least will tip over.I would not recommend that set up with that camera and lens.

Q: 7. I can adjust the locking handle with two allen wrenches, but how do I adjust the tension at the ball joints at the ends?

A: The ball joint tension can't be adjusted. I would recommend not placing anything over 6.61 lbs. Which is the rated payload.

Q: 8. I Have Impact VC 500wln lights will this stand work with this light?

A: Yes any monolight than has a 5/8" receiver like the Impact VC-500WLN can work with this stand.

Q: 9. Will this replace any halogen bulbs?? If so, which ones?? Thx!

A: The Frezzi Extended-Time 3200K LED Warm Lamp for Dimmer Mini-Fill, B&H # FRET3000LEDW, and the Frezzi Extended-Time 5000K LED Cool Lamp for Dimmer Mini-Fill, B&H # FRET5000LEDC, are both designed for use with the Frezzi EyLight Body with Front Cap, B&H # FREL, which is also compatible for use with the BAB lamp, such as the Impact BAB Flood Lamp (20W, 12V), B&H # IMBAB. For this particular fixture, the bulbs would be interchangeable. While the LED lamps may also be compatible with other lamp fixtures that use the GX5.3 base, I cannot guarantee that it will be interchangeable with all lamps of this type/design, and it would be best to inquire with the manufacturer of your light fixture before using the Frezzi Extended-Time LED lamps in other fixtures.

Q: 10. Will it work on Odyssey 7Q+ and Sony FS700? Or should I use another Magic Arm? Thanks.

A: Being that the Convergent Design Odyssey7Q+ and the Sony NEX-FS700R Super 35 Camcorder both have a threading that is compatible with the Manfrotto 143BKT bracket in this kit, you can use the 143N Magic Arm with them. This would be especially good to use if you are attaching the Odyssey 7Q + to the leg of your tripod with the Super Clamp or the camera to a flat or rounded surface with the same clamp.