Designed for large venues, the 120V 29265 Wireline Advantage 65 x 116" Motorized Projection Screen uses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

133" Diagonal / 16:9 Aspect Ratio    HD Progressive 0.6 Surface    0.6 Gain / 170° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface

Ideal for high output projectors or applications where projector brightness and screen size require low gain, the gray surface compensates for a brightly lit environment so that image contrast is preserved. In low ambient light, HD Progressive 0.6 provides deep contrast and is typically used with video. Cone: 170° Gain: 0.6

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Black-backed screen material for enhanced image quality and opacity
• Seamless screen surface

Related Questions and Answers

Q: 1. Can I attach it to DLH4 light head directly? Do I need any other accessories for using it?

A: It attaches directly to the front of the HLH4 housing; just ahead of the filter slot, and is locked in by the same rotating top clip that locks the filter in place.

Q: 2. Does it work with hive wasp?

A: This lens does not work on the Hive Wasp.

Q: 3. Does this work with elinchrom lights?

A: No, the Dedolight Projection Attachment with 85mm f/2.8 Lens is not compatible for use with Elinchrom light fixtures. While not identical, the Elinchrom Zoom Spot Attachment, B&H # ELZSAQ, would be a similar item that works with all Elinchrom monolight fixtures and may also use gobos. It allows you to focus the light, but it will have a hard edge to the light.

Q: 4. What is the focal length of the included lens?

A: The Godox BFP Flash Projection Attachment for Bowens comes with an 85mm lens.

Q: 5. what is the size of the gobos used?

A: The Godox BFP Flash Projection Attachment for Bowens uses M size gobos (2.6" / 66 mm).

Q: 6. Would this work well on a Profoto B10 light with a bowens to Profoto adapter?

A: Godox BFP Flash Projection Attachment for Bowens will work with the GTX STUDIO Bowens to Profoto Flash Head Adapter.

Q: 7. Will this fit the DLED4.1 head?

A: Yes it will.

Q: 8. Dear All, how close to the back ground wall can it be placed? Thanks

A: How close this lens can be placed in relation to a background wall would be dependent on the type of lighting being used. For example, if this lens was used with one of the Dedolight DLH4 Tungsten Lights, that would produce a greater amount of heat versus using the lens with a Dedolight DLED4.1 LED Light.

Q: 9. Is this the DP 1.1 or the universal (older model)?

A: This is the DP 1.1. It is not the universal.

Q: 10. Will this work with aputure units? Will it work with 600x/d/c?

A: The Godox BLP LED Projection Attachment for Bowens BH #GOBLP is designed for Bowens mount LED lights under 300w.