Designed for large venues, the 120V 29451 Wireline Advantage 78 x 139" Motorized Projection Screen uses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

159" Diagonal / 16:9 Aspect Ratio    Dual Vision Surface    0.9 Gain / 130° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface

Dual Vision is a flexible vinyl surface ideal for rear projection, but capable of front projection as well. Dual Vision is ideal for video projection under controlled ambient light conditions. With a wide viewing cone and light gray tint, a sharp image with no color shift is observed regardless of location in the room. Cone: 130° Gain: 0.9

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Seamless screen surface

Related Questions and Answers

Q: 1. Would this work well on a Profoto B10 light with a bowens to Profoto adapter?

A: Godox BFP Flash Projection Attachment for Bowens will work with the GTX STUDIO Bowens to Profoto Flash Head Adapter.

Q: 2. Is there a way to mount the BFP to a AD600 or even AD300?

A: The Godox BFP Flash Projection Attachment for Bowens BH #GOBFP can be attached directly to an AD600Pro. With an S2 adapter you can use it with an AD300Pro.

Q: 3. Does this work with elinchrom lights?

A: No, the Dedolight Projection Attachment with 85mm f/2.8 Lens is not compatible for use with Elinchrom light fixtures. While not identical, the Elinchrom Zoom Spot Attachment, B&H # ELZSAQ, would be a similar item that works with all Elinchrom monolight fixtures and may also use gobos. It allows you to focus the light, but it will have a hard edge to the light.

Q: 4. Does this fit Aputure Light Storm lights such as the 300dii and 120dii?

A: Yes it includes a Bowens speed ring that you will need.

Q: 5. Is there some place I can find what sizes lenses are? I'm looking for 70-200mm f/2.8 GM II Sony gears (mostly the zoom).

A: The following ruler will allow you to measure your lens for proper Smallrig seamless gear fitting. https://bhpho.to/3QsFlEO

Q: 6. Will this fit the DLED4.1 head?

A: Yes it will.

Q: 7. Will this fit on the DLED 2.1 as well? Their videos show a DP1s is this the same?

A: The B&H page that describes the DLED 2.1, in the Acessories section, lists the DPS1 as the recommended imager for the DLED 2.1.I use the MDLH4 with the DP 1.1 imager and the 85 mm 2.8 lens. As far as I can tell there are only single versions of the lenses for all their imagers, which makes perfect sense.Alternatively, if you have a Leitz slide projector, the Leitz projector lens will fit BUT without the safe travel groove on the lens AND with the danger of an indent mark on the lens if over tightened.The imager and lens combination works really well. I also use the iris diaphgram attachment to control the light spread - it all works beautifully well with my macro projects.(The iris control lever has quality issues - it is loosely glued rather than screwed in - and should never be used to remove the diaphgram from the imager. Instead, loosen the attachment tightening screw on the imager and push from the bottom. This is not in any Dedo information.)

Q: 8. Does this attach directly to the ad400 pro?

A: The Godox BFP Flash Projection Attachment for Bowens has a Bowen-S connector. You can connect this light modifier to the Godox AD400Pro Witstro All-in-One Outdoor Flash with the Bowens Mount Adapter Ring included in the box with the flash.

Q: 9. Will this work with Godox continuous lights? I want to use it for adding texture to my backdrop for video.

A: The Godox BLP LED Projection Attachment for Bowens is recommended for LED continuous lights.

Q: 10. I wanted to know if these Manfrotti 78" extension work with Impact's Varipole system. For some reason Impact doesn't make the silver extensions in 78" which is what I need now. Has anyone used them with Varipoles?

A: Yes, the Manfrotto 033 Single Extension for Autopole (78", Silver) should be compatible for use with the Impact Varipole system.