Heavy-duty adjustable collar microphone, ideal for those not wanting to use a headworn or clip-on microphone.

Unidirectional pattern for aiding in the reduction of feedback.

Ultra-slim profile for unobtrusive wearing.

High sensitivity.

Related Questions and Answers

Q: 1. Why you bought this pin and not the Avenger E250?

A: The Avenger E250 Long Double 5/8" Baby Pin is 6.0" long designed and made to fit into super clamp or any other locking 5/8" receptor.

Q: 2. What's the sound quality compared to the sennheiser mke-2?

A: The MKE-2 out-performs the B3 in its sound quality, noise and SPL specs.

Q: 3. The collar end is tapped, but not with 1/4-20 or 3/8-16. What is the spec of that tap?

A: From our measurements in the store with a caliper, it seems to be unthreaded and approximately 0.34" in diameter.

Q: 4. Need clip for cable for Sennheiser HSP wireless mic to attach to shirt collar?

A: I would recommend BH #WITC5 as a clip for this microphone.

Q: 5. Is this pin threaded to receive a 1/4 -10 double end spigot? Trying to solve attaching a Amran/Apurture LED panel.

A: This pin is not threaded at all. It's designed to be used in a pinch-clamp of a C-stand. The end with the reduced diameter is where a strobe would be added, and tightened into place by the set screw of the strobe.

Q: 6. I tried to use this on a c-stand with my elinchrom D-Lite 400W/s RX 4 Flash Head but the head does not fit on it properly. I bought the elinchrom in a bundle that included light stands. The elinchrom fits on the light stand perfectly. Now, I want to put the flash head on my c-stand. What are the proper attachments to do this to connect it to a c-stand?I bought the following products:a href= http://www.bhphotovideo.com/c/product/1086351-REG/elinchrom_el_20842_2_d_lite_rx_4_2_light.html target= _blank http://www.bhphotovideo.com/c/product/1086351-REG/elinchrom_el_20842_2_d_lite_rx_4_2_light.html/aa href= http://www.bhphotovideo.com/c/product/372016-REG/Impact_CT40MKIT_Master_Century_C_Stand.html target= _blank http://www.bhphotovideo.com/c/product/372016-REG/Impact_CT40MKIT_Master_Century_C_Stand.html/aThanks.

A: Your Elinchrom Head should fit on the 6-inch pin on the smaller, grooved, off-set end of the pin. But, first slide the small end of the pin through the appropriate-sized hole in the grip-head (on the arm extension) after turning the handle on the grip head to loosen the grip head and open the holes wide enough to slip the pin through. Then tighten the grip head handle to hold the pin in place, and to the angle you choose. Once that is done, you can then attach the Elinchrom head to the grooved end of the pin and re-adjust the angle and height.

Q: 7. Why this one costs more than Avenger E250 ? Different metal?

A: The Avenger E250 Long Double 5/8" Baby Pin is designed for use inside a super clamp or any other locking 5/8" receptor. Meanwhile, the Avenger E650 6.0" Pin with Collar is designed for use with a grip head. The collar at the end of the pin acts as an anchor to prevent the pin from sliding completely through a grip clamp.

Q: 8. Will this work as a Mic for a desktop computer?

A: If your computer has a dedicated 3.5mm microphone input, you will likely be able to record an audio signal using this microphone. However, this is not what the EX-505U was designed for and you might find the output level to be inadequate in this application. This microphone is really meant to be used with our wireless transmitters.

Q: 9. Is this pin threaded to receive a 1/4 -10 double end spigot? Trying to solve attaching a Amran/Apurture LED panel.

A: No, the hole on the bottom of the Impact 6.0" Pin is not threaded, and will not accommodate a spigot or an adapter. Please contact us at info@gradusgroup.com or the B&H Photo lighting department for more information about connecting your Amran Aperture LED panel.

Q: 10. Will this work with a Zoom H1?

A: Yes it will work OK, if you connect EX505U in the input LINE IN for microphone.