MPhatik from MeldaProduction is a multi-effect dynamic plug-in that lets you fatten and warm up your sound using amp simulation, distortion, compression, and convolution reverb, and restore the dynamics of your original signal afterwards, fully, partly, or even creatively. You can thicken your tracks without compromising the rhythmic tightness and edge of your drums, basses or other dynamic instruments.

MPhatik measures the level of the input (or side-chain), processes the input

signal using the integrated effects, then measures the output level and applies a dynamic gain to make the output level the same as the input. Adding creative possibilities, it also allows you to apply the envelope of one track onto another, and for instance use your drums to get a rhythmical pad.

To perform more complex tasks, MPhatik lets you choose which channels are affected by allowing you to select different modes such as stereo mode, mid/side mode, surround mode, and more. Other features include Automatic Gain Compensation (AGC) to avoid loudness changes, a safety brickwall limiter to ensure that the output stays below 0 dB, and adjustable upsampling to avoid aliasing.

Fatten and Warm Up Your Audio    Restore Original Dynamics    Amping/Distortion/Saturation    Convolution Reverb    Safety Brickwall Limiter    Automatic Gain Compensation    Mono, Mid/Side, Surround Processing    AAX, Audio Units, VST, VST3    Mac OS X, Windows

• Fattens and adds warmth to your audio
• Restores dynamic of compressed or distorted signals
• Apply dynamics of one track onto another one
• Side-chain input
• Advanced user interface — stylable, resizable, GPU-accelerated
• Unique visualization engine with classic meters and time graphs
• 4 x full-featured modulators which can control any set of parameters, including other modulators
• Control multiple parameters using a single Multiparameter
• M/S, single channel, up to 8 channels surround processing
• Smart Randomization wisely selects "good-sounding" combinations of parameters
• Automatic gain compensation (AGC) quickly adapts to current settings and ensures the output sounds as loud as the input
• Safety limiter provides a safety brickwall limiter, which ensures the output stays below 0 dB
• Adjustable upsampling 1x to 16x — includes both minimum-phase and high-quality linear-phase upsampling algorithms, which avoid aliasing
• Synchronization to host tempo — oscillators and modulators can automatically synchronize to the host or can be left out-of-sync
• MIDI controllers with MIDI learn — MIDI processor listens to MIDI controllers and MIDI keyboards for controlling any parameters in real time
• 64-bit audio processing can handle any sampling rate up to 192 kHz
• Extremely fast algorithms, optimized for newest AVX-capable processors
• Preset snapshots
• Global preset management and online preset exchange
• Supports all major hosts on Mac/Windows platforms
• No dongle or internet access required for activation
• Free-for-life updates entitles you to free updates, forever

Related Questions and Answers

Q: 1. what does it do?

A: Apologies, our Web Content Team is working to publish a full overview and specs page for the BirdDog Camera Director Multi-Camera PTZ Production Software. In the mean time, here is a link to BirdDog's overview of the Multi-Camera PTZ Production Software. https://birddog.tv/cameradirector-overview/

Q: 2. Greetings, I would like to know if the SKP 100 G4 is compatible with an older G3 transmitter in G band. I wish to send the audio output from a Sound Devices MM-1 preamp connected to a Sennheiser ME-66 mic (line output level). Will this work fine without an attenuator? Thank you.

A: Yes the Sennheiser SKP 100 G4 in G-band will work with a Sennheiser ME66 and G3 receiver in G-band.

Q: 3. I am trying to replace bulb..How to I safely get bulk out of part it is plugged into when deliver and installed

A: To replace lamp; Unscrew the two thumbscrews located at the rear of the unit, slideout the lamp assembly, replace bulb andreassemble. Do not forget to unplug unitbefore replacing bulb!Fuse is located underneath mains inputFor service, contact your Elation dealer

Q: 4. Does this unit remember the last settings when power is cut? Can it be powered via a wall switch tied to a half-hot outlet?

A: The CHAUVET DJ Abyss 2 LED Multicolor Water-Effect Light cannot be used with a wall switch.

Q: 5. will this work with a plain Shure SM-58?

A: Yes it will with the Shure SM-58 as well as any other dynamic microphone on the market that sports an XLR connector.

Q: 6. Will this work with tv news style interviewer microphone and Sennheiser G3 wireless system?

A: If your mic is a Dynamic microphone with an XLR connection, it will work. While this G4 Plug-on transmitter is backwards compatible with the G3 Wireless systems, make sure you order it with the same Frequency range as your existing G3 wireless system as otherwise it will not work.

Q: 7. Work with shotgun mic?

A: Hello Don - the SKP 100 G4 will work with shotgun microphones that feature battery power, such as the Sennheiser MKE 600. If you'd like to use this transmitter with a microphone that requires phantom power, please look into the SKP 500 G4 as this will provide +48V for shotguns like the MKH 416 and MKH 8060. Please note that this item is a transmitter and you'll need a full system, including a receiver, for your shoot. Options for consideration might include the EW 100 ENG G4, EW 500 FILM G4 or EW 500 BOOM G4.

Q: 8. Sennheiser EW 100-ENG G2 series and I need to replace the transmitter. Would this G4 version work with the G2 series?

A: Yes they are backwards compatible. NOTE: In order for it to work they should be in the same frequency range, or at least a good portion of the frequencies should be within range of your existing system.

Q: 9. Can I use a Sennheiser ME II with this if I use an adapter and if so, which adapter?

A: No, the ME 2-II lavalier microphone will not work with the SKP 100 G4 transmitter. The mic requires plug-in power and the SKP 100 plug-on transmitter does not supply any power at all. The Sennheiser SK 100 G4 Wireless Bodypack Transmitter A: 516 to 558 MHz (B&H # SESK100G4A) is the compatible transmitter to use with the ME 2-II. It does have the correct connector for attaching the ME 2-II and also supplies plug-in power for the mic. Just be certain to match the frequency band with your receiver.

Q: 10. Is this rated for 110v-220v input?

A: Yes, the Eartec 2-Port Multi-Charger with US Plug can be used for 110 to 220V inputs, but this particular item is shipped with a US plug. If you need the same item for 220V, you can order the Eartec 2-Port Multi-Charger with EU Plug Adapter (B&H # EACHLX2EEU).