Intended for use with the MV50 amplifier head, the VOX BC108 is a 1x8” speaker cabinet capable of handling 25W at 8 Ohms. At 8.6 lb, it’s rather portable, and features a semi-open back structure to facilitate a more focused sound, especially in the bass range of the frequency spectrum. Even though it is compact and portable, at 25W it can offer enough volume for practicing at home or gigging in small venues such as coffee shops.

On the rear of the cab you’ll find two 1/4" speaker jacks, both of which can be used as an input. Daisy-chaining this cab to another BC108 is possible by making use of whichever 1/4" jack is not currently employed. In this case, you can run one 1/4" speaker cable from the MV50—or other compatible amp—to the cabinet, and run another cable from the BC108 to your secondary speaker. The output impedance will reduce to 4 Ohms when set up in such a manner.

Designed for MV50 Amplifier Head    25W RMS Power Handling    1 x 8" 8-Ohm Speaker    Tight Response in Bass Range    Semi-Open Design    Portable at 8.6 lb    2 x 1/4" Speaker Inputs    Can Be Daisy-Chained with Another BC108

Related Questions and Answers

Q: 1. Can you plug it in in a Hercules 4mx

A: Yes - via the speakers 1/4 mono input. Hercules offers 4x mono connectors in '' jack format, to connect to a public address amplifier or speakers. Keep in mind that this speaker needs an amplifier to power it.

Q: 2. What type of cable is needed to connect a modeler to this cabinet - i.e., instrument cable or speaker cable?

A: The HeadRush FRFR-108 MKII 1x8" 2000W Full-Range Powered Cabinet accepts mic input via XLR, and line input via 1/4" TRS. It does not accept instrument level input.

Q: 3. Can I terminate (8) CAT6A to a patch panel first before the VDA? I am concerned about the weight of cables connected to the VDA

A: Yes, it would be possible to terminate the Ethernet cables before the VDA of the KanexPro 1x8 HDMI Distribution Amplifier and Cat 5e/6 Extender Kit (18 Gb/s) as long as the patches are one to one. Please note that your transmission distance may be reduced when using a patch panel.

Q: 4. Is the cabinet covered with real wood veneer or vinyl?

A: Elac has confirmed the following.. "The cabinet is a simulated wood look vinyl veneer".

Q: 5. How long is the attachment cable? thx!

A: The attached cable to connect the extension cable is approximately 3-feet long.

Q: 6. Will the distribution amp support multiple resolutions, or will it "dumb down" all resolutions to the lowest resolution?

A: KanexPro 1x8 HDMI Distribution Amplifier and Cat 5e/6 Extender Kit (18 Gb/s) would take HD and 4k contend into the extender and send out up to 8 of the same signal over HDMI. It does not have a scaler so whatever resolution or framerate you put in would be duplicated on the 8 HDMI outputs. The kit supports resolutions UP to 4k@50/60hz 4:4:4.

Q: 7. the sound is really good with good bass and trebles clear ?

A: This speaker provides a well balanced range of tone for general monitoring situations.

Q: 8. Do I need a amplifier if I'm hooking this up to a dj mixer? If so what is a good cheap one

A: Pyle Pro PTA1400 Professional Stereo Power Amplifier (350W/Channel @ 8 Ohms)B&H # PYPTA1400

Q: 9. Are the tubes included?

A: Yes, the tubes are included within the VOX AC41-12 4W RMS 1x12 Combo Amplifier. There is a specific 90-day warranty for the included tubes.

Q: 10. What is the frequency response range for this cabinet?

A: The frequency range of the HeadRush FRFR-108 MKII 1x8" 2000W Full-Range Powered Cabinet is 52 Hz – 22 kHz (-10 dB).