Suitable for electric guitars, the Soul POG combines Electro-Harmonix’s Soul Food overdrive pedal with the Nano POG polyphonic octave generator into one multi-effect pedal, giving you distortion, octave generation, and various combinations thereof. The unit provides white knobs for the discrete Nano POG section and black knobs for the separate Soul Food section, making it clear which parameter affects which part of the pedal. Two footswitches are also provided, one to engage each circuit, with corresponding LEDs visibly announcing the engaged or disengaged state of the pedal.

Of course, you can run both sections of the unit at the same time. If you choose to do so, you’ll find the toggle switch in the center of the stompbox quite handy, as it changes the order of effects in the signal chain, putting one section before the other, arranged in a manner suitable to your needs.

The pedal utilizes an interesting routing scheme, giving you a mono 1/4" input and two 1/4" output jacks—one for dry signal, and one for processed signal. The effect output provides audio from the Soul POG, so you can separate your distorted/octavized sound and route it to its own destination point. The dry output, on the other hand, routes the buffered, bypassed input straight into to a destination of your choice, and will not be affected by the Dry knob.

Also provided is an effects loop, complete with 1/4” send and return jacks. Through this loop, you can put effects in the signal path between the Soul Food and Nano POG sections of the pedal, thereby increasing your sonic possibilities. Included with the pedal is an Electro-Harmonix 9.6DC-200BI power supply.

Combines Soul Food & Nano POG Pedals    Transparent Overdrive & Octave Pedal    Volume, Treble & Drive Controls    Octave, Sub Octave & Dry Controls    Sections Work Independently or Together    Signal Chain Switchable    Dry & Processed Outputs    1/4" FX Loop for Introducing Other FX    Buffered Bypass on Soul Food Section    Included Power Supply

DRIVE Knob: This controls the amount of input gain. As you turn this knob clockwise, the overdrive ranges from a clean boost—in the fully counter-clockwise position—to classic distortion (in the fully clockwise setting). In addition, turning this knob clockwise brings out more midrange in your tone.

TREBLE Knob: This knob acts like a conventional tone knob on a tone stack. When set to 12 o’clock (50%), the tone is neutral. As you turn the knob clockwise from the 12 o’clock setting, the treble gain increases, making your overall sound brighter. Turn the dial counter-clockwise from 12 o’clock, and the high end is reduced, emphasizing the lows.

VOL Knob: This control sets the output level of the Soul Food section of the Soul POG. As it’s turned clockwise, the output volume increases.

SOUL FOOD Footswitch and LED: This footswitch selects whether the Soul Food section is engaged or in bypass mode. When the Soul Food is engaged, its corresponding LED is lit. The Soul Food circuit in the Soul POG is always in buffered bypass.

DRY Knob: This controls the output volume of the Dry signal at the Effect Out jack. As this knob is turned clockwise, the volume of the Dry signal at the Effect Out jack increases.

SUB OCTAVE Knob: This dial controls the output volume of the Sub Octave signal, which is tone generated at one octave (half-frequency) below the original input signal. As this knob is rotated clockwise, its level increases.

OCTAVE UP Knob: This knob controls the output volume of the Octave Up signal, which is tone-generated at one octave (double-frequency) above the original input signal. As this knob is rotated clockwise, its level increases.

MODE Switch: This toggle switch changes how the Octave Up signal responds to your playing. With the Mode LED off, you’ll be utilizing the default Nano POG algorithm, which is better for single-note runs, and provides lower latency. With the Mode LED on, the upper-octave notes contain enhanced harmonics and improved polyphonic capabilities.

POG Footswitch and LED: The POG footswitch selects whether the Nano POG is engaged or in buffered bypass. When the effect is engaged, its corresponding LED is lit.

EFFECT ORDER Switch: This toggle switch, located in the middle of the Soul POG, selects which effect comes first in the signal chain. With the switch to the right, the signal chain is Soul Food going into Nano POG. With the switch to the left, the signal chain is Nano POG going into Soul Food.

Related Questions and Answers

Q: 1. What's the length of the cable?

A: The Blackmagic Design URSA power supply offers a 46inch cable.

Q: 2. I have some devices in my rack that require 9vdc - how can I power that with this?

A: The SANUS CAPT01 MultiVolt Power Supply is not intended for use with devices that require 9V DC power. The CAPT01 features seven 12V DC power connections that are always on, four thermostat-controlled 12V DC connections, five 12V DC lights-only connections, and four 5V USB ports. A separate port is the input for the included thermostat.

Q: 3. Is there a rack mount kit for this model?

A: I don't use it in that configuration. Check the manufacturers website

Q: 4. Does this work with Blackmagic URSA Mini Pro 4.6 G2?

A: Yes it will.

Q: 5. Comes with EURO plug?

A: It is configured for the USA/North America only. A European adapter is not included.

Q: 6. does this adapter work with 240v in australia?

A: The Shure PS124L Power Supplies are region specific. The Shure products we carry here at B&H are all 120VAC compatible only.

Q: 7. Does this come with a power cord?

A: Yes, the Telex PS-20 come with an IEC power cable.

Q: 8. My EM300 diversity receiver unit says 300mA input but this power supply says 400mA. Will this still be ok to use?

A: Its fine the adapter will regulate it self to 300ma. This will work.

Q: 9. Would this work for a Remote Audio BDS system with a Sound Devices 664?

A: Sorry but BDS systems use NP1 batteries only thus they cannot be AC/DC powered. You can use a NP1 battery like this plus this kit.

Q: 10. Will this power supply work with the older G2 systems?

A: The Sennheiser NT 2-3-US is compatible with G2 and G3 series receivers.