The 500-Series, RNLA500 Really Nice Leveling Amplifier from FMR Audio is an APT500-series rack version of the popular Really Nice Leveling Amplifier. It can be used to add some compression-induced character to your vocal, bass, drum mix, and guitar audio tracks, and provides signal control in applications for recording, broadcast TV, post-production, and more.

The RNLA500 is built with overcurrent protection and prevents a rare failure from bringing down your whole 500-series rack. There is an early-warning power supply detection circuit that enters bypass and a front panel switch to avoid power-down pops. Other features include a dot, gain-reduction display, sealed, C&K toggle switches, and red-anodized, machined aluminum knobs. With the 18 gauge, electro-galvanized enclosure, it will keep the electronics safe from harm and protect against EMI interference.

Additionally, the compressor's sound exhibits a sonic neutrality and permits a level-of-control without adding unwanted artifacts. It has a sonic gooeyness that is creamy and smooth, and adds a slight hesitancy to respond, which is a key performance parameter. Although the RNLA500 is a VCA-based compressor, the algorithm controls it in a manner that puts the essence of opto-compressors in a more modern and controllable compressor. Overall, the RNLA500 is clean, but with a hint of attitude that's under your control.

500-Series Version of the RNLA    Balanced Input and Output    Linkable for Stereo Operation    Overcurrent Protection Circuits    Linear & Logarithmic Release Modes    Dot Gain-Reduction Display    Red-Anodized, Machined Aluminum Knobs

Related Questions and Answers

Q: 1. I have a huge hiss problem connecting my beeznees mic to the bae compressor in to this la2a what could it be?

A: Hissing in any piece of audio gear is indicative of electronic noise, due to either poor quality in components or improper gain staging. Keep in mind every time an audio device is added to the chain, the noise floor increases.

Q: 2. Does this device work with 220v power or is it only 110v?

A: Yes, the FMR Audio RNC1773 offers a power Supply 100-240 VAC, 47/63 Hz 12 VDC, 500 mA regulated, 2.1 mm barrel connector

Q: 3. Does the TA-4-LB-HK need a separate 100mm video bowl to install on the TVC-45 Tripod Apex?

A: No.

Q: 4. Got this handle from BH last year. Lately I notice the rubber grib at the handle will slip and rotate when I about to fully tighten the bowl. wWas that the design or intention? it made me frustrated that the bowl seems couldnt fully tightened. Any expert can assist on this or any current users experience this ? Thanks

A: The rubber grip should not be moving or slipping when you attempt to tighten it.

Q: 5. I presently have TVC-34 Versa S.3 Mk2 tripod purchased from B&H, will this work with Sachtler Ace XL Fluid Head ?

A: TVC-34 Versa S.3 Mk2 tripod will not work with the Sachtler Ace XL Fluid Head (75mm Bowl) BH #SAS21500004 as the later only works with tripod legs of 75mm Bowl.

Q: 6. Is this the proper Leveling Base for the RRS TVC 44 tripod?

A: The Really Right Stuff TA-4 Leveling Base with 4.5" Handle and Hook is compatible with the Really Right Stuff TVC-44 Versa Series 4 Mk2 Carbon Fiber Tripod.

Q: 7. Will the RRS TA-4-LEVELING BASE fit my RRS Versa Tripod TVC-34L MK2?

A: The Really Right Stuff TA-4 Leveling Base with Low-Profile Knob is only compatible with Series 4 tripods; TVC-34L MK2 is a Series 3 tripod, so RRS TA-3 is compatible: https://www.bhphotovideo.com/c/product/1337700-REG/really_right_stuff_ta_3_lb_lp_ta_3_leveling_base_with.html

Q: 8. Will this work on a Benro C373T Tripod as it has a 75mm bowl?

A: Yes, it will fit.

Q: 9. The description states that this levelling base will also fit a Gitzo Systematic series 3 tripod. Since the top plate on a Series 3 tripod is exactly the same size as a Series 2 Systematic tripod, this base must also fit Series 2 and I also believe Series 4 then. True or False?

A: This is only for RRS Versa S.3 Tripods

Q: 10. Will the RRS TA-4-LB Leveling Base fit on an FLM CP38-L4 II tripod (this tripod has a 100mm bowl head area?)

A: According to RRS, the TA-4-LB fits on most standard 100mm diameter bowl tripods. The one thing I would caution is that the low-profile knob sits very close to the apex/spider of the tripod and it might be hard to operate in certain situations depending on how your tripod is set up/situated.