This set of four Leg Clamps from Kessler Crane connects two separately available Kwik Rails or other third-party rails with four legs to create a slider system for the Kessler Crane Shuttle Dolly. Each heavy-duty clamp features two rod clamps with locking levers to secure the rail to a leg, which allows you to adjust the height of the track. The clamps support any rail diameter from 1.635 to 1.652".

Attach Legs to Kwik Rail    Set of 4 x Clamps with Locking Levers    Fits 1.635 to 1.652" Diameter Rail    Allows Shuttle Dolly Leg Adjustment

Kessler Crane Kwik Rail

Kessler Crane Shuttle Dolly

Third-party rail from 1.635 to 1.652" in diameter

Related Questions and Answers

Q: 1. can I mount the Manfrotto 509HD on here and still be able to mount the Kessler Crane KC-12 on top of the manfrotto head?

A: You should be able to mount any bowl head to the kpod with the right accessories. I don't have the kc-12, but I assume as long as the kc-12 has 1/4 or 3/8 mounting holes it should work with your manfrotto. That being said, I don't think you'll be satisfied with the setup as your manfrotto head won't be able to take on that much load. Crane + Camera + Counterweights would certainly go over the 29lb capacity of that head.

Q: 2. will this work on a nikon 70-200 f2.8ED and the Arca swiss P0?

A: Yes it can. It has the 1/4-20" thread and is Arca compatible.

Q: 3. Will this fit on a Manfrotto head that uses 501PL quick release plate?

A: No it will not. This plate is not wide enough and to my knowledge will only work with its matching Kessler receiver. For example, I use one that is mounted on my slider, and I have a Kwik Short Camera Plate, that I can attach to the bottom of a small fluid head. The Kessler receiver is mounted to a 100mm half-ball, that sits in my 100mm tripod bowl. Then I can switch between a slider and fluid head on one tripod without removing and switching plates.

Q: 4. Should/could this be used to mount the second shooter unit to a slider that has the Quick release receiver on it?Thanks.

A: I do not have a second shooter or never used one, but I would assume you could. I have used this to attach several things to the Kessler receiver. I have the pocket jib, and I attached this to the bottom so it was easier and faster to use on a tripod. I would double check with Kessler but I would assume you would be able to.

Q: 5. the "plate" on the bottom, does it fit arca-swiss or Manfrotto PL type mount?

A: NO it will Not

Q: 6. How do I mount the Kessler crane on this tripod?

A: The best bet is to get the Hercules Head and a Kessler quick release plate for it.

Q: 7. will the bottom of this plate sit flat on the table ?? with the plate attached to the camera ?

A: No, it will not. It has two screw heads protruding. They serve as catches so the plate does not slide out of the head.

Q: 8. Does the plate actually weigh 1 lb? That seems kind of high, didn't know if the weight was referring to the shipping weight ...thanks

A: Yea it does. If not exactly, it's close to it. It's a solid piece of metal. Still holding up for me no prob.

Q: 9. How do we attach the Ronin2 mount on this thing?

A: A Ronin 2 can not be mounted directly to the Kessler Crane KillShock Isolator System unless it is mounted upside down so that the Ronin 2 can hand down from the mounting plate. If you were to mount the Ronin 2 in this way you can use the CineMilled R2 Main Mount for DJI Ronin 2 (BH #CICM021) to attach the Ronin 2 to the Kessler Crane KillShock Isolator System.

Q: 10. Is there anything similar to this for 1.25" speed rail?

A: The most similar alterative to the Kessler Crane Leg Clamps for Kwik Rail System (Set of 4) for 1.25" speed rail would be the CineMilled 2" Billet Trailer Hitch Adapter for 1.25" Speed Rail Tubing (BH #CICM3100).