With the GyroVu 11" Articulated Arm with Quick Release for Ronin-M and MōVI you can secure a monitor to your FREEFLY MōVI or DJI Ronin-M gimbal, both of which utilize a 25mm bar size. Secure a monitor to the end of the arm using the 1/4"-20 thread and unlock the center joint to place it for comfortable viewing. The 1/4"-20 accessory mount sits on a quick release, allowing for quicker setups compared to just screwing the monitor onto the arm. The arm itself features a rosette in the center joint, ensuring the arm doesn't slip from wear over time.

11" Extended Length    12 lb Load Capacity    1/4"-20 Accessory Thread    Quick Release Accessory Mount    Center Rosette Prevents Slippage

Related Questions and Answers

Q: 1. Is it possible to provide the weight of the arm without the cold shoe adapter?

A: The weight of the ANDYCINE Rugged Articulating Magic Arm is about 9oz.

Q: 2. does the shoe come off? And is there a threaded bolt? I don't want the shoe part

A: The shoe will remove revealing a 1/4"-20 female bushing.

Q: 3. Will the mini clamp tighten down on 15mm dslr rig rod?

A: Yes, it will tighten onto a 15mm rod.

Q: 4. Does this fit a 19 mm adapter on Flycam Comfort Stabilizing Arm & VestCMFT-AV?

A: Yes,This will work with 19mm post adapters.

Q: 5. Whats the maximum weight this can hold?

A: This arm does not work well. We are using it with a tiny camera and it is difficult to get it into position. It does not lock into position well. To answer your question, we have very little weight and I worry it will fall out of position at some point. Fortunately we are able to not touch that camera now that it is set up.

Q: 6. I have read around and have heard reviews stating that this unit does not contain screws long enough to attach to a Ronin-MX bar. Will this product mount without needing to purchase an additional pack of long screws?

A: GyroVu does not list this mount as compatible with the MX. Any adaptation is on your own and out of warranty. GyroVu does list this different but similar purpose mount for the MX. It is less expensive. GyroVu 7 Heavy-Duty Articulated Arm Mount for DJI Ronin-M/MX & FREEFLY MoVI (Quick Release) B&H # GYGVPMMA7HQ.

Q: 7. Does this works with a Ronin- S and a Liliputus A7s?

A: It depends on how you wish to mount the arm to the stabilizer but you can use this accessory on the Ronin S in order to complete the build. SmallRig Mounting Clamp for DJI Ronin S Gimbal B&H # SM2221 MFR # 2221. The Axler articulating arm offers a 1/4"-20 screw on both ends. One end can screw to the Lilliput monitor and the other end can screw into the SmallRig accessory. https://bhpho.to/2DFuIsP

Q: 8. Will this hold an Odyssey 7Q and Sony LP battery?

A: I use this mount on my Ronin-M with a Atomos Ninja Asassin that has the large Sony camcorder batts powering it and the mount has zero issues. Hope that helps.

Q: 9. Hello! I just bought one of these. I can't seem to figure out how to get the ball head to stand still, its always loose. Is there a way to tighten it up?

A: you should be able to make it stay still by tightening BOTH red pieces

Q: 10. would this 11" arm be good for mounting a Godox M1 (B&H # GOM1) to something like an oben Table top tripod (BH #OBTT100)? I don't want to use something ridiculously large like a full blown cstand/lightstand/camera tripod to mount a 1/2 lb godox M1 unit, but would like more angle and height versatility, that presumably a 11" arm would give. But not sure if it's a wise way to get there, if the 11" arm would be too top heavy for the oben tabletop tripod/tip over, etc. I would be looking to use it in vehicle interiors and behind subjects of a greenscreen to create separation. I find having the tabletop pod on the floor or on a carseat isnt verstatile enough (light looks too underlit and unnatural) and don't have places to clamp the godox m1 inside a car without damaging cars i don't own, etc. And similarly, the angle of the light for backlighting a subject to create separation w a greenscreen isn't high off the ground enough to get an effective wrap around a seated subject, if am just using the tripod on the floor. Plus it would be great to be able to angle the light to fine tune a greenscreen key, etc.

A: The Manfrotto 209 Tabletop Tripod (BH #MA209), would be more suitable to support the Gyrovu Heavy-Duty Articulated Arm (11-), as it has a much higher load capacity. You may also want to consider a small sandbag for further reaches of the arm with the Godox M1 light. https://bhpho.to/3CWx6en