Featuring a sliding camera plate, SHAPE's REVOLT VCT Universal Baseplate can accommodate rigs of varying sizes. Simply attach your camera via 1/4"-20 or 3/8"-16 screws to the top plate, and slide it onto the shoulder plate. Fore and aft movement allows you to balance the weight of your setup properly. Further adjustments can be made by moving the shoulder pad. The 15mm rod clamps at the front and rear of the baseplate allow you to secure 15mm accessories such as a matte box, follow focus, lens motors, lens supports, battery plates, or external recorders. Since the front rod clamp is attached to the top plate, the rod-mounted accessories don't need to be repositioned as the rig is adjusted. Additionally, handles can be mounted to the ARRI standard rosettes on either side of the plate. When not shoulder-mounted, the baseplate can be secured to a standard VCT-14 ENG quick release in a matter of seconds, saving time on set.

REVOLT VCT Universal Baseplate    Shoulder Pad, Dual Rubber Handgrips    Matte Box, Follow Focus Pro    1/4"-20 & 3/8"-16 Threads, 4 x 15mm Rods    Sliding Camera Plate, Hardware Kit    Anti-Twist Rubber Pads Protect Camera

The sliding baseplate provides a quick positioning of your camera and accessories for an optimal adjustment of your camera's balance center.

Height-adjustable rod clamp for aligning the 15mm rods at the proper LWS height in relation to the optical axis.

Front and rear rod clamps allow you to extend your rig forwards and backwards.

Built-in storage areas for extra screws and the Allen wrench ensure that necessary adjustment tools are always close at hand.

Safety pins and spring-loaded levers prevent the top plate from sliding unintentionally.

Soft and ergonomic shoulder pad.

Related Questions and Answers

Q: 1. Where might I mount a large V-mount battery?

A: This unit is made out of 15mm rods. You could use a V-Mount battery plate like this from IndiPro Tools. https://bhpho.to/3jjtUNW

Q: 2. I can't seem to get my Canon 5D Mark III to fit with the lens properly in the matte box. The lens comes in too low. Does anyone have any tips to make fit correctly?

A: Under the front of the matte box is a screw. Loosen that and adjust the height.

Q: 3. I was at the 2015 NAB Show, and I'm almost certain I saw one of these with a Canon C100 Mark II mounted on it. Is that possible? Is there an additional plate needed for that? I don't remember seeing one, but just wanted to make sure before I pursued purchasing one of these.

A: The SHAPE Sony FS7 Bundle Rig with Follow Focus is specifically for the FS7. If you mounted a C100 Mark II on it, it would be missing a right handle arm. See below for a suggested SHAPE rig for the C Series.You might have seen this rig for the C300. It is made by Zacuto. It is a very nicely tricked out rig that will also work with the C100.

Q: 4. Will this work with the fx30?

A: The SHAPE Shoulder Mount with Matte Box and Follow Focus for Sony FX3 will also be a perfect fit for the Sony FX30.

Q: 5. Is it possible to get this rig with a 4x56 matte box instead?

A: This is a kit put together by Shape which we do not offer with 4 x 5.65 matte box. However, you could always purchase BH #SHA73SM instead and add a different matte box, along with a different follow focus. https://bhpho.to/2KHbx5z

Q: 6. Would this fit a Panasonic AG-DVX200?

A: Hello Stephen, Thank you for your question! Our BP22 would surely fit with this camera given its side LCD monitor that opens up. Because of the location of the monitor though, it might be a bit high, but if you plan on framing with an external monitor, the ergonomy of the whole setup would be a better fit. We hope this helps and we thank you for your interest in our products. The SHAPE team

Q: 7. With this rig, you wouldn't need to buy a separate camera cage, correct?

A: Yes, you do not have to purchase a separate camera cage with the FILMCITY DSLR Shoulder Mount Rig with Matte Box & Follow Focus Kit since there are 1/4"-20 threads on the rig to mount accessories.

Q: 8. es compatible con la sony a73?

A: Yes, this can work with the Sony a7iii. Sí, esto puede funcionar con la Sony a7iii.

Q: 9. Will this cage/shoulder mount/matte box etc. with the Sony Alpha a7R IV?

A: The A7R IV will have a slightly different design than past models. It will not fit properly in the cage.

Q: 10. and how can you add a lamp and a microphone?

A: We sell a number of Rod Clamps and other adapters that will enable you to mount additional gear to this rig. Some of the most popular options are articulating arms that have integrated rod clamps. Here are a few examples CAMVATE Articulating Magic Arm with 15mm Single Rod Clamp (7") B&H # CAC1100 MFR # C1100 Niceyrig 15mm LWS Rod Clamp with 7" Articulating Magic Arm B&H # NI107 MFR # 107 GyroVu 7" Articulating Arm with 15mm Rod Clamp B&H # GYGVPMM15A7H MFR # GVP-MM15A7H