Wireless Security Pin Hole Camera

Impact 6" Baby Pin Wall Plate

Product Code: ga43044
Availability: In Stock

$38.85 $48.95

Qty

0 reviews Write a review

Description
Reviews (0)

Constructed of chrome-plated steel, this Impact 6" Baby Pin Wall Plate is a must-have accessory on any type of production set. All that's needed is a flat surface for its base to attach and user-supplied screws to mount it on walls, ceilings, or floors. Alternately, it's often gaffer-taped to apple boxes or the floor to temporarily support lighting equipment at a very low angle. The industry-standard 5/8" diameter pin is welded to the base for extra strength and fits a very wide variety of lights and other gear with a matching 5/8" receiver. The 5/8" pin has a hole for a safety wire.

5/8" Diameter Pin Chrome-Plated Steel Construction 8 x Anchor Points Safety Cable Hole

Parameters
Mounting	5/8" / 16 mm Stud
Material	Steel
Dimensions	L: 3.1 x W: 5.9" / L: 8.0 x W: 15.0 cm (Base) L: 6.0" / L: 15.2 cm (Stud)
Weight	1.5 lb / 680 g
Packaging Info
Package Weight	1.455 lb
Box Dimensions (LxWxH)	6.65 x 6.25 x 3.4"

6" pin supports lights with a 5/8" receiver

Heavy-duty chrome-plated steel with welded pin

Use as a support when a light stand is too large for your space

Screw down the wall plate via the eight anchor points

Hole in the pin for a safety cable to avoid hazards

Related Questions and Answers

Q: 1. what is the distance between the holes?

A: The large Outside holes are 6 centimeters by 13 centimeters on center. The small Inner holes are 4 centimeters by 12 centimeters on center.

Q: 2. Is the pin removable?

A: The pin is welded in place.

Q: 3. How much weight can this hold?

A: I have used it up to 8 lbs, & to Secure it, I always suggest a Safety cable. Impact Safety Cable (18") BH #IMSC1.518 • MFR #SC-1815

Q: 4. How much weight can these support? I want to use three of these to hang a 37-pound canvas backdrop on my wall (the backdrop is mounted on a top rail made of wood with three holes for hanging).

A: These are welded steel. The weak point will be the wall and how you anchor them.

Q: 5. What's the difference between this and the identically named SRP-115?

A: This plate is the same as the SRP-115 produced by Impact.

Q: 6. What diameter are the screw holes, and how far apart are the holes from each other?

A: According to the manufacturer you can use 6d or 8d nails, or drywall screws. They do not have a measurement for the spacing.

Q: 7. What is the length (end-to-end) of the entire piece when it is straight?

A: It's about 9" (22.9cm) long.

Q: 8. can it be ceiling mounted?

A: As long as you have adequate support from above yes. I would look to anchor all four of the bolt holes into something very solid like a floor joist from the floor above. Be careful about finding a mounting surface that will provide adequate width so that you anchor all 4 corners using the provided holes. I would not bolt this to a drywall ceiling and attach anything weighing more than a few pounds to it. If you bolt this to the ceiling then you should also consider what you are going to attach to the pin and ensure that you can grip that pin firmly enough that it can hang upside-down with all of the weight trying to pull away form the pin.

Q: 9. Why has B&H not updated the product title & description to explain it is not threaded?

A: The Impact SRP-110P 6" Baby Pin listed above has a 1/4"-20 female thread in front of the pin (mounting side) and a 3/8”-16 female thread in the back of the pin (collar side).

Q: 10. Which hole is the "safety cable hole"?

A: safety cable goes on the Baby Pin

There are no reviews for this product.