Designed for large venues, the 120V 29266G Wireline Advantage 65 x 116" Motorized Projection Screen uses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

133" Diagonal / 16:9 Aspect Ratio    HD Progressive 0.9 Surface    0.9 Gain / 170° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface    Flangeless Case

Ideal for moderate to high output projectors, the light gray surface provides balance between color reproduction and image contrast. Cone: 170° Gain: 0.9

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Black-backed screen material for enhanced image quality and opacity
• Seamless screen surface

Case does not have trim flange, making it suitable for non-ceiling-recessed applications.

Related Questions and Answers

Q: 1. Will this work with aputure units? Will it work with 600x/d/c?

A: The Godox BLP LED Projection Attachment for Bowens BH #GOBLP is designed for Bowens mount LED lights under 300w.

Q: 2. what is the size of the gobos used?

A: The Godox BFP Flash Projection Attachment for Bowens uses M size gobos (2.6" / 66 mm).

Q: 3. Is there a way to mount the BFP to a AD600 or even AD300?

A: The Godox BFP Flash Projection Attachment for Bowens BH #GOBFP can be attached directly to an AD600Pro. With an S2 adapter you can use it with an AD300Pro.

Q: 4. I would like to find a similar projector to fit elinchrom 600w studio lights. Ideally with optional metal leaves to control the area to be lighted. Does anyone have any recommendations?

A: Please review the following item. https://bhpho.to/3pEq4Us

Q: 5. What's the difference between the DP1 and the DP1.1 ?

A: The DP 1.1 is an updated version of the DP1 which now has a double lens system and is optimized for use with the DLED lamp heads. This system would help increase the light output and offer better optical performance.

Q: 6. Can it be used with a bowens mount adapter?

A: This projector is designed to work with a Dedolight. It will not work with a Bowens mount.

Q: 7. Is the speed ring interchangeable? If so, what size is it?

A: The speedring that is part of the Godox BFP Flash Projection Attachment for Bowens is not interchangeable.

Q: 8. Will this fit the DLED4.1 head?

A: Yes it will.

Q: 9. Does this attach directly to the ad400 pro?

A: The Godox BFP Flash Projection Attachment for Bowens has a Bowen-S connector. You can connect this light modifier to the Godox AD400Pro Witstro All-in-One Outdoor Flash with the Bowens Mount Adapter Ring included in the box with the flash.

Q: 10. Will this fit on the DLED 2.1 as well? Their videos show a DP1s is this the same?

A: The B&H page that describes the DLED 2.1, in the Acessories section, lists the DPS1 as the recommended imager for the DLED 2.1.I use the MDLH4 with the DP 1.1 imager and the 85 mm 2.8 lens. As far as I can tell there are only single versions of the lenses for all their imagers, which makes perfect sense.Alternatively, if you have a Leitz slide projector, the Leitz projector lens will fit BUT without the safe travel groove on the lens AND with the danger of an indent mark on the lens if over tightened.The imager and lens combination works really well. I also use the iris diaphgram attachment to control the light spread - it all works beautifully well with my macro projects.(The iris control lever has quality issues - it is loosely glued rather than screwed in - and should never be used to remove the diaphgram from the imager. Instead, loosen the attachment tightening screw on the imager and push from the bottom. This is not in any Dedo information.)