Designed for large venues, the 220V 29216EG Wireline Advantage 92 x 164" Motorized Projection Screen uses thin steel cables instead of black drop to lower the screen to an appropriate viewing height. Once the screen is installed, the screen's trim conceals the rough opening in your ceiling, eliminating the need to complete additional trim work. Sliding installation brackets help make it easy to attach the screen housing to the structure above the drop ceiling.

188" Diagonal / 16:9 Aspect Ratio    HD Progressive 1.3 Surface    1.3 Gain / 150° Viewing Angle    Suspended from Cable up to 29'    Slim-Tab, Low-Profile Tab-Tensioning    Hand-Held Remote Included    Built-In Radio-Frequency Motor    Seamless, Black-Backed Screen Surface    Flangeless Case

Ideal for applications where projector brightness and screen size require an increase in gain, the white surface offers high-fidelity color reproduction, and allows for more flexibility with ambient light conditions. This surface works for video as well as charts and graphs in a corporate setting. Cone 150° Gain: 1.3

• Up to 29' of cable to accommodate appropriate viewing height in rooms with high ceilings
• Slim-Tab, a lower profile and stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• UL Plenum-rated case
• Works with separately available radio-frequency control accessories such as a single-channel wall switch, dry contact interface, and RS-232 interface
• Black-backed screen material for enhanced image quality and opacity
• Seamless screen surface

Case does not have trim flange, making it suitable for non-ceiling-recessed applications.

Related Questions and Answers

Q: 1. Will this work over Cat 5e?

A: Yes, they will work over Cat 5e.

Q: 2. Does this function with a Pro Display XDR?

A: Yes, the Optical Cables by Corning Thunderbolt 3 USB Type-C Male Optical Cable works with the Pro Display XDR.

Q: 3. Does this allow you to transfer data from a nas to Mac at 40Gb/s? I thought the limit was 3m before you start losing bandwidth.

A: The Optical Cables by Corning Thunderbolt 3 USB Type-C Male Optical Cable supports up to 40Gb/s by using high quality optical cable "This 49.2' thin and light optical cable has male-to-male USB Type-C Thunderbolt 3 connectors and is designed to transfer data at up to 40 Gb/s."

Q: 4. will this cable work to connect apple studio display to an apple studio desktop computer?

A: Yes, this Optical Cables by Corning Thunderbolt 3 USB Type-C Male Optical Cable (82') will connect Apple Studio Display to an Apple Studio desktop computer.

Q: 5. Has this cable been tested for Thunderbolt 4 support? Or, if I When I plug this cable into a TB4 device (TB4 hub), will it force it back to TB3 feature set?

A: If you connect a thunderbolt 3 cable to thunderbolt 4 port, you will be limited to thunderbolt 3 speeds and features.

Q: 6. can this be used for Pro Audio Setup? Connecting Audio Interface with Computer?

A: If the Audio Interface is using a Thunderbolt 3 or USB type-C lower rated output as well as the Computer having a Thunderbolt 3 input, yes this cable is ideal for that setup.

Q: 7. Will it work if only the receiver is plugged into 5V power, or does the transmitter need it as well?

A: Yes. Both units must be powered via barrel (5 VDC at 1 A) Input.

Q: 8. WILL THIS RUN THE APPLE XDR 6K DISPLAY? THANKS!

A: Yes this cable will support the Apple XDR 6k display at full resolution.

Q: 9. What is the latency?

A: There is no published spec regarding latency of the Optical Cables by Corning Thunderbolt 3 USB Type-C Male Optical Cable (49.2'). Any latency would be so negligible that it would very likely not be noticed.

Q: 10. Can it be used to clean the dust off speaker driver (Edifier S3000 Pro)?

A: No, the METROVAC DataVac Electric Duster 500 is not recommended for use to clean the dust off of a speaker driver. The force of the air may be too strong and could permanently damage the speaker. Instead, use a soft brush or a vacuum hose with a soft brush attachment to remove the dust. You could also try to carefully use a can of compressed air in short bursts from a slight distance to avoid damage from the air pressure, but the soft brush is probably the safest method.