The 7X-500VIN Single-Channel Vintage Edition Compressor/Limiter from Lindell Audio fits all 500 series compatible power supplies. It features a high-pass sidechain filter that allows you to focus the unit's response. It features 3-way switches that allow you to set the compressor's attack, release, and ratio. With Mix Knob, you can mix dry and wet signals (parallel compression).

• 500 Series format compressor
• FET-based technology
• Variable mix control lets you blend compressed and uncompressed signals in parallel for maximum compression without losing transients
• 3-step switched attack and release times make for accurate dynamics
• 3-mode (off, 100 Hz, and 300 Hz) high-pass sidechain filter lets you focus your dynamics
• Choose from mild 4:1, heavy 12:1, and "all-in" 100:1 compression ratios
• True-bypass hardware preserves your sound when bypassed
• 20-LED gain-reduction metering lets you keep an eye on the mix
• Dual OPA1731 amplifiers

Related Questions and Answers

Q: 1. Can I create my own preset and store it in this interface and use it without running the app on my iOS or macOS?

A: There are 5 Presets which are built in to the Motiv MVi, no need for the App. Five built-in DSP preset modes (Speech, Singing, Flat, Acoustic Instrument, and Loud) While in a PreSet, it is possible to tweak it to your liking, HOWEVER, when you exit the Preset, that PreSet reverts back to the "Factory" preset parameters You may also "tweak" settings on the Compression or EQ as needed. On your phone, the App may be used to store your own PreSets (100+) and name them and also control the Motiv MVi. In this scenario, you would need to run the App to recall your PreSets...

Q: 2. I have 2 unrelated mono line level signals that I would like to level control. Can I use one TSD-ALC2 to do this?

A: You would need an Atlas Sound TSD-ALC2 for each of your sources to be able to individually control the level on those sources.

Q: 3. Is the 1/4" input stereo or mono, and can it take a line feed from a mixer (as opposed to mic feed)?

A: I feed the mic input on this unit from the aux send line output (pre-fader) on my Mackie mixer with no issues. Just make sure you turn the aux master control way down to avoid signal clipping.

Q: 4. What specifically is this unit used for, How does it work. Then maybe I can try it out for what I need?

A: The Atlas Sound TSD-ALC2 - Audio Level Controller and Limiter is an automatic 2-channel audio level controller and limiter designed to allow designers and installers to set predetermined maximum source levels. The device is useful for installations with multiple program sources of varying output levels such as satellite receivers, MP3 players, and more.The unit is inserted in line with these sources so that the audience will not be distracted during high-volume commercial breaks or when different inputs are selected. The device is useful in retail stores, restaurants, sports bars, hotels, event centers, and other similar facilities.The device features unbalanced stereo RCA input and output connectors, a threshold level control, a ramp speed selector, and output gain adjustment controls. The unit also works well when used in conjunction with Atlas Strategy Series Mixer Amplifiers.The device is designed to be energy efficient and meets most energy standards. One 24 VDC power supply (sold separately) can power multiple units, depending on overall current requirements. The front-panel controls can be locked to prevent unauthorized changes using the included front panel security covers. ---------------------------------------------------------------------OWNER S MANUAL: https://a href= http://www.cie-group.com/files/tsdalc2_manl.pdf target= _blank www.cie-group.com/files/tsdalc2_manl.pdf/a

Q: 5. Can this be used on the Radial Engineering KL-8 inserts to apply limiting across all channels?

A: The Drawmer SP2120 Dual-Channel Speaker Protector and Brickwall Limiter should be compatible with the Radial KL-8 to limit the master channel.

Q: 6. Will the Shure MOTIV MVi interface retain the last panel settings (volume / mode / mute) when it is disconnect & reconnected? What happens when you unplug it from one computer & plug the USB into another?

A: There is no internal battery, therefore settings would not be saved once power is disconnected.

Q: 7. Hi! I would like to connect a XLR 48v phantom power mic to my Gh5S for better sound. Would this item work for that???

A: Yes, this is designed for exactly that use.

Q: 8. Can this device be made to stay in Super Nice mode across power cycles?

A: Settings will not be remembered in the case of a power failure or a power reset. NORMAL MODE: Mode Selection This mode is selected upon power up of the RNC. If the SUPER NICE indicator lamp is extinguished, then NORMAL MODE is selected. SUPER N ICE MODE Mode Selection: This mode must be manually selected by depressing the SUPER NICE switch until the SUPER NICE indicator lamp is on.

Q: 9. Hey! I have a Sennheiser MD 46 dynamic microphone. Do you know if the preamps in the linkflex-ad2 are good enough to boost this dynamic microphone? I would like to use the linkflex to connect the MD 46 to an iPhone (and possibly my good old Zoom H2). Would that work?

A: As previosly answered: 6249490Approved The Linkflex specs show up tp 20dB of gain. which may be enough gain, depending on your subjects volume level. One question is, how much electronic noise will be added to the signal? Another question is, how will the MD46 sound if you must turn the Linflex up to full level on its level control. A big part of how a microphone will sound, is the impedance of the mic pre (the Linkflex) amplifier. The noise spec is not listed in the spec sheet, so I would be weary of this. It may be a lot to include, but this is the reason these; Cloudlifter CL-1, are included in the signal chain with dynamic mics, to improve, not only gain, but performance... Comica Specs: Comica Audio LINKFLEX-AD2 Specs General In-Line Accessory Type Pre-Amplifier Gain Up to +20 dB Connectivity I/O 1 x 1/8" / 3.5 mm TRRS Male Output 1 x 1/8" / 3.5 mm TRS Female Headphone Output 1 x Combo XLR-1/4" TS Female Mic/Hi-Z Input Performance Frequency Response 20 Hz to 20 kHz ±1 dB THD+N 0.02% (2-Kilohm Load)

Q: 10. What is the brand and model microphone and headphone included in the bundle?

A: The Kit include a Shure PGA58 Dynamic Mic with 15' XLR to XLR cable and Shure SRH240A Professional Headphones. It appears as though the configuration buttons on our website are reversed, but this is the link to the Kit: https://www.bhphotovideo.com/c/product/1560690-REG/shure_motiv_mvi_digital_recording.html