The brown Single Earset Mic for Select Azden Systems from Microphone Madness is an ultralow-profile, single-earloop microphone with high gain before feedback designed to deliver detail and clarity even in noisy spaces or near loudspeakers. The flexible earloop comfortably conforms to your ear and the boom can be precisely placed to deliver accurate sound. This mic is intended for voice reinforcement in theater plays, speeches, lectures, male and female vocals, and more.

Locking 3.5mm Male Connector    For Azden Wireless Systems    Miniature Low-Profile Single-Ear Design    Flexible Earloop    Sturdy Boom    Hypercardioid Polar Pattern    50 Hz to 15 kHz Frequency Response    High Gain Before Feedback    For Speech & Vocals    Windscreen & Holding Clip Included

Locking 3.5mm male connector for compatibility with the following Azden wireless systems: 15BT and 35BT

Related Questions and Answers

Q: 1. Will this work with a digital recorder or a VIXIA 82 camcorder?

A: thank you for your question. This will work with the Vixia 82 an with any audio recorder that has a stereo mic input and can provide plug in power.

Q: 2. Dumb question, would this work if I plugged this into an average aux port?

A: Whether you are referencing an Aux In port or an Aux Out port it will not work because mic signal is much lowerl than line level signal like from a headphone output for example. Because of that, the ESM-1-MN would only be compatible with a microphone input.

Q: 3. Good afternoonI have an old Sony-urx-p1-utx-b1 kit, but has lost my lavalier.Does this Azden lavalier work on my kit?RegardsJonny PedersenThe Steadicam Operaotr

A: It is very unlikely the Azden EX-503 will work with your UTX-B1. The connector on the Sony transmitter is a locking 3.5mm screw connector. The Azden is not, also the wiring may be different. The lav normally used as a replacement would be the Sony ECM-77BMP.

Q: 4. I'm wondering if I bend it to be used on the other ear if the microphone will break? It's currently set up for the left ear.

A: The boom on the Polsen ESM-1-35H Single-Sided Earset Microphone is flexible and adjustable, so it should not break if you bend it to curve for use on the right ear.

Q: 5. Could this be used with a Rode VXLR+ 3.5mm TRS female to XLR male adapter with phantom power converter to use it as a wired mic?

A: Yes, the Polsen ESM-1-35H Single-Sided Earset Microphone for Sennheiser Transmitters (B&H # POESM135H) can be used with the RODE VXLR+ 3.5mm TRS Female to XLR Male Adapter with Phantom Power Converter (B&H # ROVXLRP) in order to connect it to a wired XLR microphone input. As another option, you could use the similar Polsen ESM-1-MN Single-Sided Earset Microphone for Recorders and Wireless Transmitters (B&H # POESM1MN) for connection to a standard 3.5mm TRS mic input with plug-in power. Either version of the earset mic can be used with the VXLR+ adapter for connection to an XLR mic input. The difference between the two models is that the version for Sennheiser transmitters has a locking 3.5mm connector and the version for recorders has a standard non-locking 3.5mm connector.

Q: 6. Will this work with the Zoom h1?

A: I have used this product with the zoom H6 only, and it works well.I am not sure about the zoom h1. If there is a connection on the device, it should work just fine.

Q: 7. Is the ear frame flexible? (Can the circular part be shaped, or will it snap?)

A: Yes. The single-sided earclip on the Polsen ESM-1-TA4 easily conforms to your ear and holds the mic in place for active applications such as fitness, mobile journalism, house of worship, and more.

Q: 8. is this microphone compatible with the "Azden WLX-PRO+i VHF wireless microphone system for cameras & mobile devices"?

A: Yes, the HS-9 microphone is fully compatible with the WLX-PRO+i wireless system.

Q: 9. Will this ear piece work with the Shure BLX1 J10 wireless transmitter?

A: Yes, The Polson ESM-A-TA4 will work with the Sony BLX transmitters,

Q: 10. Can this be plugged into a Sennheiser transmitter? The Sennheiser has a three contact 1/8inch connector, this has only two contacts. Anyone do this already? Thanks!

A: I can't really comment on Sennheiser's equipment, however, if the transmitter has a 3 contact mini-jack, it could be for a balanced connection. If this is the case, it is possible that the 2 contact plug on the EX-503L would work, it just would not be balanced.