The black Single Earset Mic for Select Sennheiser Systems from Microphone Madness is an ultralow-profile, single-earloop microphone with high gain before feedback designed to deliver detail and clarity even in noisy spaces or near loudspeakers. The flexible earloop comfortably conforms to your ear and the boom can be precisely placed to deliver accurate sound. This mic is intended for voice reinforcement in theater plays, speeches, lectures, male and female vocals, and more.

Locking 3.5mm Male Connector    For Sennheiser Wireless Systems    Miniature Low-Profile Single-Ear Design    Flexible Earloop    Sturdy Boom    Hypercardioid Polar Pattern    50 Hz to 15 kHz Frequency Response    High Gain Before Feedback    For Speech & Vocals    Windscreen & Holding Clip Included

Locking 3.5mm male connector for compatibility with the following Sennheiser wireless systems: Evolution Series, EW100, EW300, EW500, G2, G3, SK 1093, SK 20, and SK 2020 Tour

Related Questions and Answers

Q: 1. Will the receiver on this work with remote antennae?

A: Yes it will. Depending on what you want to do, you may need to get an antenna distribtion/splitter such as the Sennheiser ASA 214 (for multiple systems), and/or use low loss 50ohm cables for runs in excess of 50'

Q: 2. Dumb question, would this work if I plugged this into an average aux port?

A: Whether you are referencing an Aux In port or an Aux Out port it will not work because mic signal is much lowerl than line level signal like from a headphone output for example. Because of that, the ESM-1-MN would only be compatible with a microphone input.

Q: 3. Will this ear piece work with the Shure BLX1 J10 wireless transmitter?

A: Yes, The Polson ESM-A-TA4 will work with the Sony BLX transmitters,

Q: 4. Is the 1/8 inch jack straight or a right angle?

A: It is at a right angle.

Q: 5. would these work for a wireless system? for example, the new Rode Wireless Go system or Sennheiser XSW kits? do transmitters typically provide the plug in power needed for these lavs?

A: This will work with the Rode Go systems very well, I've used them together in the past and overall had a good experience. However it does not work with Sennheiser wireless system since they have a proprietary locking pin, so when buying lavs for Sennheiser systems it either needs to be made buy Sennheiser or for Sennheiser.

Q: 6. Is the ear frame flexible? (Can the circular part be shaped, or will it snap?)

A: Yes. The single-sided earclip on the Polsen ESM-1-TA4 easily conforms to your ear and holds the mic in place for active applications such as fitness, mobile journalism, house of worship, and more.

Q: 7. Does it require 48V phantom power?

A: No, the Polsen ESM-1-MN Single-Sided Earset Microphone does not require 48V of phantom power, it requires 1.5 to 5V of plug-in power which can be supplied through the 3.5mm mic input on many recorders or cameras, as well as by the 3.5mm jack on certain computers.

Q: 8. What is the Range from mic to receiver

A: These systems work line of sight and base specs off of optimal conditions. Realistically, 100-150 feet would work even though most of the time they will claim around 300 feet.

Q: 9. Where is this product manufactured?

A: The Sennheiser XSW 2-835-A is currently manufactured in Taiwan.

Q: 10. What are people using to mount these, and to minimize clothing noise?

A: It's really more about where you are mounting these rather than about what you are mounting it with.I use basic Rycote Undercovers as the sticky element and then I find a dead spot under the subject's clothing.