More than just a way to power your camera, the RED DSMC2 V-LOCK I/O Expander provides a variety of input/output connections in addition to a V-Lock mount for your DSMC2 camera. The Expander is made from magnesium, so it is lightweight yet strong. It enables powering your camera from a V-Mount battery or by an alternate DC source via cable, and you can set it to automatically boot your camera up once power is connected. It provides both 3G-SDI and HDMI outputs, as well as control and sync outputs.

Built-in USB and auxiliary power outputs enable powering accessories and limiting the number of power splitter and converter boxes hanging from your camera. Audio is not forgotten by RED, and the Expander features both an analog stereo input and a stereo headphone jack. It is compatible with the WEAPON 8K S35, WEAPON 6K, as well as the EPIC/SCARLET-W, and the RAVEN.

DC Power input    Auto Boot-Up on Power-On    3G-SDI, HDMI 1.2 Output    Control & Sync Ports    USB Power Output    AUX Power Output    Stereo Analog Input    Stereo Headphone Output    FOR WEAPON 8K S35, WEAPON 6K    For EPIC/SCARLET-W, RAVEN

The Expander features a physical switch that allows you to enable the camera to automatically boot up when power is applied. This is a useful feature for when the camera is in a difficult-to-access position.

Since the V-Lock I/O Expander communicates with your camera, and allows electronic signals and video output, it requires that your DSMC2 camera has firmware v6.2.17 or later installed.

The Expander simplifies your power and output situation when shooting, and can be removed if you want your camera to have a smaller profile for stash-cam, gimbal, or drone shooting.

Related Questions and Answers

Q: 1. Can you run HDMI and SDI at the same time? RED GEMINI

A: You will only be able to use one output at a time.

Q: 2. What 80mm Touch and Go quick release adapters work with this?

A: Yes, the RED DIGITAL CINEMA KOMODO Expander Module, is compatible with the GLOBAL DYNAMICS UNITED 80mm Touch N Go System.

Q: 3. How much does this weigh?

A: Approximately 0.13 lbs (59 g)​​​​

Q: 4. Are the 1/4-20s on the front to attach LW 15mm rods?

A: There are 1/4-20s on the front but are for accessory mounting, you can attach rods to the threads if you chose to

Q: 5. Can the GPI port be used as an SDI out? I want to run a Portkeys OEYE EVF and a SmallHD Cine 7 at the same time.

A: No, the GPI cannot be used as a SDI video output.

Q: 6. What is a bracket that can mount 15mm rods to the two 1/4-20s in the front?

A: This simple Axler Rod Bridge Adapter should do the trick: https://bhpho.to/2KgyKya

Q: 7. How does the module attach to the camera? Will it work if I have the tilta komodo camera cage on?

A: There is a ¼-20 and 3/8-16 captive mounting screw at the bottom of the Expander that attaches to the bottom of the RED Komodo. The Expander Module will be able to attach to the 1/4-20 thread underneath the Tilta cage but won't be secured through the Expander's 3/8-26 screw.

Q: 8. Is it compatible with any v-mount battery or red brick only?

A: I know it works with my IDX slims. I think that's the lowest you can go as far as wattage though. Anything from there on up, you should be fine. Honestly though, unless you already have VLock batteries, I'd go for the bricks. Just get two. They last WAY longer and you can see the percentage of battery life on the monitor.

Q: 9. I'm guessing this does not work for DSMC3 cameras such as the new Red Raptor. Is there any way to make it work/what is a good alternative?

A: Unfortunately the RED DIGITAL CINEMA DSMC2 Side Handle is not compatible with RED DSMC3 cameras like the RED V-Raptor. Since the V-Raptor does not have a dedicated R/S trigger handle, you can take advantage of the EXT port and rig a 3rd party accessory to control R/S.

Q: 10. Is this compatible with Red Helium 8K?

A: Because the RED Helium 8K is a RED DSMC2 camera, the RED DSMC2 V-LOCK I/O Expander is compatible with the Helium.