The AES/EBU 1x2 Passive Splitter from Whirlwind is a passive unit that delivers two identical AES/EBU signals from a single stream. The design utilizes a dual secondary transformer on the input and a separate isolation transformer for each output. With the three-transformer circuit, the splitter maintains good data integrity and high amounts of isolation between outputs.

XLR Female Input    2 x XLR Male Outputs    32 to 192 kHz Sample Rate    Low Capacitance    Low Jitter    Made in the USA

Gold-plated XLR female input to two gold-plated XLR male outputs

Fast rise time, low capacitance

Low jitter

Low pulse aberration

Made in the USA

Related Questions and Answers

Q: 1. CAN MY FIOS SET TOP BOX OUTPUT BECOME INPUT TOP SPLITTER RESULTING IN TWO TVS GETTING THE SAME STATION?

A: Yes, the KanexPro 1x2 HDMI Splitter will send the signal coming in to two different destinations. You can use this to split video signal coming from your set top box to two destinations.

Q: 2. Can the AES/EBU work as a standard XLR splitter?

A: The Sescom SES-AES-EBU-Y Impedance Matching AES/EBU Y-Splitter Cable is designed specifically for digital audio, not analog audio. There can be a problem with impedance mismatch if you use it with analog audio and standard XLR cables, since digital audio is typically 120 ohms and analog audio is 50 ohms. If you need an XLR Y-adapter for analog audio signal, you can use the Hosa Technology YXM-101.5 XLR Female to Dual XLR Male Audio Y-Cable - 18" (B&H # HOYCXF2XM18).

Q: 3. why can't I just use a standard XLR "Y" cable to split AES?

A: Without getting technical: while there is a chance it may work - and it usually works ok the other way around (using AES/EBU cables on analog gear - it is not recommended to use non AES/EBU cables on digital gear. You can experiment but it is not recommended

Q: 4. do they make an adapter that will power this from a Canon or Nikon battery?

A: Canon and Nikon batteries are 7 dvc volts and this runs on 5 dcv. While it would be possible to build such a power adapter at this time we do not know such a device. If you need a HDMI splitter that cannot be powered, you might success with this splitter. Keep in mind that you need high quality short cables to have success with it. By judging by the reviews, your mileage may vary. Please email us if you have further questions. E-Mail: provideo@a href= http://bhphotovideo.com target= _blank bhphotovideo.com./a

Q: 5. I have a Panasonic AG-UX90 Camera and I am trying to use both a Magewell capture device (for livestreaming) and an Elvid Video monitor (to mirror what is coming out of the camera). Both need an HDMI connection, but I only have one OUT on the camera. If I split the signal, can I do both (different) things at the same time?

A: I have had excellent success with these.Make sure you know what kind of signal is being output.Make sure all your input devices can digest the signal.If one type of signal does not work, you may have to switchto a different signal.Remember these switches are programmable, so make sure the dip switches are set correctly.

Q: 6. Does this cable's db 25 connector follow the Tascam or Yamaha protocol?

A: The Avid DB25-XLR M+F AES/EBU DigiSnake follows the Tascam protocol for AES/ EBU digital connections only. This cable is not designed to be used with an analog DB25 connection.

Q: 7. Does this unit require external power? if so, how much and on what kind of connector?

A: The Whirlwind Line Balancer/Splitter requires no external power and is designed to split a single line level input signal into two balanced line level outputs. A choice of two output configurations is provided: one direct output and one isolated output, or two isolated outputs. The Line Balancer/ Splitter uses Whirlwinds TRSP-600L transformer and has a frequency response of 20 to 20kHz, 1dB @ +2OdBm.On the Line Balancer/Splitter are two male XLR jacks, one female XLR jack, a 14 jack and three switches as outlined below:INPUTEither of the two input connectors, a female XLR jack or a 14 TRS jack (Tip = Pin 2 and Ring = Pin 3) can be used for connection from a line level source, balanced or unbalanced. Use only one input at a time.OUTPUTSThe male XLR output connectors can be configured in one of two ways. The ISOLATED OUT/SPLIT 1 is always transformer isolated and the DIRECT OUT/SPLIT 2 is either directly connected to the input or transformer isolated, depending on the position of the OUTPUT SELECT switch.OUTPUT SELECTThis push-button switch selects the output mode of the unit. In the out position, the DIRECT OUT/SPLIT 2 provides a direct output signal and the ISOLATED OUT/SPLIT 1 provides a balanced 600 isolated signal. In the in position (the center of the switch changes to orange) both output connectors provide a balanced 150 ?isolated signal that is attenuated by 6dB from the input.GND/LIFTSEach of these switches disconnects the ground between the inputs and the XLR outputs when set to the LIFT position. Grounds remain connected when set to the GND position.This product is warranted to be free of defects in materials or workmanship to the original purchaser for a period of 3 years from the date of purchase.

Q: 8. Is the Power supply included ?

A: Included in the box are: KanexPro 1x4 HDMI Splitter Power Supply Limited 1-Year Warranty

Q: 9. Could I hook this up to a Dslr HDMI and split it into a monitor and audio recorder timecode?

A: Absolutely, can't think of any reason why you couldn't

Q: 10. How long can I expect this device to last in a setting where it is sending a signal from a laptop to 3 monitors 24/7 (i.e. every day, all day long)? Thanks.

A: Yes, as long as the unit is kept in a cool working environment with temps no higher then 70 degrees, the unit will run all daylong 24/7.