With the Watson Pro D-Tap 1x4 Splitter Cable you can power up to four devices from a single D-Tap connection. The cable itself is 23.5" long, so you can conveniently position the four-output end of the cable wherever you need it on your rig. For best operation, ensure that the accessories you are powering don't exceed the maximum current output of the power source.

Splits 1 D-Tap into 4 Outputs    Power up to 4 Devices from 1 D-Tap    23.5" Length

Related Questions and Answers

Q: 1. Since this is 5V DC, could this be powered with a USB to barrel adapter?

A: Theoretically yes, the KanexPro 1x4 HDMI Splitter should be capable of being powered by a USB barrel adapter. However, please note that KanexPro does not officially support using USB power sources for this product. Please use caution as KanexPro may not provide support if your product malfunctions while powered via a USB to barrel pin adapter cable.

Q: 2. Does this work for HDMI cable that is 100ft long?

A: We would not recommend this product for a cable run that is in excess of 50 feet.

Q: 3. ideally, i have 8 monitors that will form 1 large display. can this splitter project 1 small screen display source to the 8 monitors as 1 big screen?

A: Sorry, no, it cannot work that way. All this would do is give you 8 separate videos at the same time. For an affordable video wall solution you could use 4 HD TV's and make one image with this controller. Gefen HD Video Wall Controller B&H # GEHDVWC144 (-----Copy and Paste this number to the B&H website search box and click Go. )

Q: 4. Will this product create a new HDMI source?

A: This product takes in a single HDMI signal and turns it in to two HDMI signals.

Q: 5. Does this splitter work for both t.v and projectors?

A: I have only used it for projectors but I don't see why not...keep in mind it's 1080 res not WUXGA

Q: 6. Can this be used to split the video output to a monitor and to a Teradek Cube in a Canon C-300 Mark II?

A: You could use this to split the HDMI signal from a Canon C300 to a monitor and a Teradek Cube. However, this device is better for permanent installations. If that is what you are doing, that is fine. However, for splitting the HDMI signal while on set in active situations, we suggest using a monitor with a HDMI loop through to the Teradek as a more convenient solution.

Q: 7. Does it have an screw holes at the back?

A: There are no mounting points on the Watson Pro D-Tap 1x4 Splitter Cable.

Q: 8. Does this cable work with the Teradek Spark 4k Receiver and or transmitter?

A: Yes, This cable would work with the Spark 4k. Here is more info from Teradek -The DC barrel jack connector is the same as used on the Vidiu, Vidiu Pro and other Teradek and Paralinx devices. It has an outer diameter (OD) of 5.5 mm, an inner diameter (ID) of 2.1 mm, and a barrel length of 9.5 mm. The polarity is center/tip positive, the outer ring is GND.

Q: 9. Can I power both a zacuto gratical eye and a SmallHD502 using this adapter - most of these splitters are rated for max of 10W, whereas these two devices wils require approximately 13W at full tilt. If not this Watson Dtap splitter, has anyone used another splitter for greater than 10W draw successfully? Thanks!

A: I'm pretty sure the rating is in amps, not watts. 14.4 volts * 10 amps = 144 watts.

Q: 10. Can you cascade these units to reach more monitors?

A: YES, CAN BE USED IN CASCADE TO ACHIEVE MORE MONITORS