The Lectrosonics SMWBBCUP is a kit for adding a spring wire belt clip to SMWB Wideband Transmitters. In addition to the clip, all the gear you need to attach it is provided, including a set screw, a thumb screw, and a hex key.

Matched Aluminum Bracket    Stainless Steel Spring Clip    For Use with SMWB Wideband Transmitter    Can be Used with the Antenna Up or Down    Lower Profile than Spring-Loaded Clip    Includes Hex Key    Includes Set Screw    Includes Thumb Screw

The spring wire belt clip allows the transmitter to be worn on a belt or other wardrobe item where a low profile is required.

With this clip, antenna will point up when the transmitter is worn on a belt.

Related Questions and Answers

Q: 1. Can I plug this directly into an SMV transmitter that's set to IFB mode and get a better signal?

A: Yes, in theory the Lectrosonics SNA600a Adjustable Dipole Antenna's BNC connection could be adapted to the "SMA" type antenna connection on a Lectrosonics SMv transmitter to widen the transmitters output signal.

Q: 2. How i setup Lectrosonics SNA600a or Sennheiser A2003UHFwith Sennheiser Reiceiver 112G3? Is it feasible?

A: The SNA600a is like a slide rule. You loosen the screws and adjust the length so it matches the scale to the frequency you are operation on. Then tighten the screws and rotate the 2 arms so they are at 90 degreed to the scale. The Sennheiser antenna is not adjustable and covers the whole of the UHF range. These are 2 different kinds of antennas. The SNA600a is omnidirectional and the Sennheiser A2003UHF is directional. Which one is best would depend on the situation you are working in. Think of an omnidirectional mic vs. a cardioid. They have different pickup patterns and serve different purposes.

Q: 3. Sorry for the question, but this doesn't look like it has a 2.5mm screw in termination, but it says it's compatible with the UM190. This screw in termination will still work? Just want to make sure before I order it.

A: For the older model UM190 without the SMA screw on antenna connection the Remote Audio ANL5 is an alternative.

Q: 4. What is the spacing of the holes on the back of the plate?

A: Hi Jesse, the dimensions are as follows: Diameter of the holes: 2,5mm; horizontal distance: 58mm; vertical distance: 74,20mm Does this help? Kind regards!

Q: 5. Will this fit on an H5?

A: No

Q: 6. Is it possible to use the SNA600a to boost the range of the sony uwp with sma mod?

A: In theory, yes, the Lectrosonics SNA600a Adjustable Dipole Antenna could be adapted for use with an SMA connection on a third party wireless receiver such as those from Sony's UWP line.

Q: 7. Does the BCA107 belt clip fit the BP2T-S?

A: The belt clip is designed to work with the AC107 battery adapters. This is the link for the adapters, a href= http://bhpho.to/1wfpHsQ. target= _blank http://bhpho.to/1wfpHsQ./a

Q: 8. Do they just push-on (fall-off?) or are these heat-shrink?

A: The Lectrosonics Color Coded Transmitter Antenna Caps push onto the top of Lectrosonics' "AMM" style antennae and provide a snug fit that does not require heat shrink to secure. Once installed, these caps should not come off unless intentionally removed by the user.

Q: 9. Will this clip fit the mount on the back of the F3 recorder?

A: The Zoom F3 has a 1/4''-20 thread on the back of it. It does not have a thread that would fit the screw hole size required by the ZBCF1 Belt Clip that would fit into the back of the F1, that threading is smaller.

Q: 10. What exactly do I need to connect the SNA600A to my Lectro src dual receiver? Do I need both the BNC cable and an adapter?

A: The Lectrosonics SNA600a Adjustable Dipole Antenna uses a 50 Ohm BNC connector to interface with the host device.