The lightweight ARRI Single Support Rod (5.9", 19mm) is designed to support a lens motor driving an Ultra or Master Prime lens mounted in the ARRI SAM-3 Stabilizer Adapter Mount. This stainless steel rod may also be used for any rig where space constrictions dictate the use of a shorter 19mm rod.

1 x 5.9", 19mm Rod    Use with SAM-3 Stabilizer Adapter Mount    Use for Lens Motor Support    Lightweight Stainless Steel

Related Questions and Answers

Q: 1. Do you think it will fit OConnor O-Rig Pro Kit B&H # OCORCS MFR # C1257-0001?

A: It works for my Nikon 24-70 and Sigma Art 24-35 lens, and keeps them from bouncing around. For a shoulder rig I like things tightened up and this works.

Q: 2. Can this be used on the fx6?

A: yes, you can mount an Fx6 to the ARRI Mounting Plate with 15mm Rod Support for Sony FS7II & FX9 Cameras.

Q: 3. I'm a little confused. Will these work with just a 15mm LWS rods configuration? Like bright tangerine leftfield 3 for ursa?

A: No, the Wooden Camera Universal Lens Support (19mm/15mm Studio) is designed for 19mm and 15mm Studio systems; 15mm LWS is a different standard that uses different spacing, so this will not work with 15mm LWS systems.

Q: 4. It works with Tilta TT-03-GJ Rig Follow Focus Kit ? Thanks.

A: This Wooden Camera Lens Support will work with the Tilta. However, the lens will determine the length of the rods and exactly how well everything works together.

Q: 5. I have zacuto recoil rig, V1 for my Sony fs5. Will this work suitable for my Nikon 70-200mm? Or is there another suitable lens support system that can screw into the foot of the lens?

A: It will work. You can always use the cradle. My issue is the shaft that goes vertically through the bridge is too long. If that is not an issue for you then this is a good deal.

Q: 6. Will this work with the Tilta Arri Standard Dovetail and baseplate? The rails sit wider than say the Zacuto universal baseplate.

A: Hello,The LS-T05 is made for standard 15mm rod systems. If I understand the baseplate you are referencing correctly, that is a 19mm system and is incompatible with the LS-T05 or LS-T05-A, depending on your lens.

Q: 7. I have a studio-width bridge plate, but it uses 15mm rods. Will this lens support work with 15mm rods that have studio spacing?

A: Hello Dan, Thank you for your question. In the case of a 15mm Studio spacing plate, our 15MM STUDIO LENS SUPPORT which you can find here: https://www.shapewlb.com/shape-lens-support-for-15-mm-studio-bridge-plate We hope this helps and we thank you for your interest in our products. The SHAPE team

Q: 8. Would this fit in the Canon LH-E1 lens support (#CALHE1) if I remove the Y support part?

A: Yes, the Tilta 15mm LWS Rod Lens Support would fit in the bottom of the Canon LH-E1 Lens Holder after removing the Y lens adapter and using the included 3/8"-16 to 1/4"-20 adapter.

Q: 9. Will it work with the DZO PICTOR ZOOM LENS on my FS5?

A: Yes. One of my favs to use at this unit allows horizontal / Vertical adjustment for more flexibility.

Q: 10. The space in between the rods is 100 mm. Turned out to be too wide for the standard SHAPE Universal Lens Support. Anyone out there that knows a lens support compatible with this ?

A: Yes. it is called the SHAPE Lens Support for Studio Bridge Plate (15mm) (B&H # SHLEN15 MFR # LEN15)