Designed to filter electrical current, the RX30 Filter Cord from Juice Goose features a single 3' power cord with a right-angle plug on one end and three receptacles placed 90° apart from one another on the other end. This filter cord also offers 1020-joule transient energy absorption, 3000 amp maximum applied surge current protection, and 6000-volt maximum applied surge pulse protection.

1020-Joule Energy Absorption    3000A Max. Applied Surge Current    120 VAC, 60 Hz    10A Max. Current Load

Juice Goose RX Series power protection technology is particularly valuable because it works against ground line (common mode) as well as hot to neutral (normal mode) events. While ground line surges and disturbances don't typically cause catastrophic damage, they can result in operating failures and improper performance of digital processing equipment.

Compared with the low operating voltage of processor logic, a power anomaly of even 1 or 2 volts on data lines or logic grounds can cause problems. That's why the RX Series products limit ground line voltage surges to only 1/2 volt.

RX Series products also protect against more dramatic events. Connected equipment is safe from surges up to 6000 volts at 3000 amps on hot, neutral, and ground.

The RX Series design includes a differential transformer, lots of filtering capacitance, and surge diverting components. Control circuitry provides protection from external wiring faults including hot-neutral reversal, missing ground, and overvoltage. RX technology delivers performance enhancement and protection comparable to an isolation transformer - but at a fraction of the price and in a fraction of the space.

The cord improves performance of HD monitors and projectors while protecting your valuable investment. When high-frequency interference reaches your HD image through the power cord, image quality is lost along with much of the reason for going HD in the first place. At the same time, dangerous high-energy events you may or may not notice can shorten the life of your video machine.

The Juice Goose RX 30 is built into the middle of a power cord ("Filtercord") to provide a convenient, easy-to-install package for use with non-racked equipment such as digital signage monitors, media players, and projectors. It can also be used as added protection for a

rack-mounted power strip. The RX 30 features a three-foot power source cable with a right-angle plug to lie flat against a wall.

The power outlet side of the RX 30 includes three receptacles placed 90 degrees from each other to accommodate multiple components including AC adapters. This design allows for better filter module placement and connection with hard-to-reach AC outlets.

Related Questions and Answers

Q: 1. What gauge is the wire in this cord?

A: The Comprehensive Standard PC Power Cord feature an 18 gauge conductor size.

Q: 2. Digital Juice Butterfly C-Stand Frame Clamps (Pair)..will the work with a Westcott Scrim Jim 4x4? The frame is wider on these than the original westcotts scrims.

A: I use these clamps with 4x4 scrim jim cine frames. They are a bit beefy for the job but they are solid. The clamps manage to fit in a cstand arm or knuckle but not very well, they are large and more suited to a roller. They are also bulky to transport but I feel it's worth it. I'm happy they can hold a larger frame should I need a 6x6 or an 8x8.

Q: 3. Will it conceal/cover a round electrical extension cord?

A: The channel that the cord fits into is a about 3/4 . As long as your cord is not larger than that it should work. You will also need to stretch out the product and put heavy weight on it for it to lay flat,

Q: 4. Will these work on an iPad - record and listen?

A: Yes it will.

Q: 5. Hello, and thank you in advance for your responses. What is the maximum width of the stand when fully assembled and setup for use? Richard Martinez, Houston, Texas.

A: The kit comes with 4 cross bars. Connected together the maximum width is 12 feet wide.

Q: 6. Will this fit an Epson projector? I bought a similar replacement cord from Office Depot yesterday, but the female end of it cord has corners that are about 1mm, so it doesn't fit. Any ideas?

A: The female end looks like an IEC 320 C13 and that should have large chamfered corners to fit the socket on the unit. A C13 mates with a C14 which is normally the recessed blades on the unit. If your cord has small chamfers it won't fit. I would make sure the male part on the unit is in fact a C14, measure it if need be and get a C13 female ended cord. Most of that stuff is standardized but you can never be too sure. Some gear has proprietary fittings to force you to buy only their stuff so I would check that out as well. Good luck.

Q: 7. HI Does this cord work on long exposure ?

A: The Hasselblad X1D offers very long exposures in the camera itself so the Hasselblad Release Cord X for X1D-50c Camera is only used to take the picture without needing to touch the camera.

Q: 8. do these work with an IMAC?

A: These are designed for devices with a single headphone/mic jack like a tablet or phone. On an iMac, these would only allow you to hear, not speak.

Q: 9. Is this 4amp?

A: This adapter produces only 100-250 mA.

Q: 10. can I use this on office carpeting?

A: The Belkin 6' Cord Concealer includes a double-sided adhesive tape which may work with a carpet floor, but due to the limited published material by the manufacturer in the quality of the adhesive, I'm inclined to recommend a better solution given the high friction that exists between carpet material and Polyurethane; B&H # ELED1010BK and B&H # ELED1050BK. The Elasco Dropover is a product well built, designed to stay put in high traffic office environments.