Power your Lectro SR receiver with the Cable Techniques CT-BDS-SR, a 24" right-angle 761K locking to right-angle locking DC powering cable for Lectrosonics SRc/SRb/SRa receivers with SREXT/SRBATTSLED, SMBATELIM, and LRBATELIM powered by DC Distro Systems from Remote Audio, PSC, and Sound Guys Solutions.

For Lectro SR Receivers    761K RA Locking Coaxial Connector    Lectrosonics RA Locking Coaxial    26 AWG

Related Questions and Answers

Q: 1. This says wired for Sennheiser. Shouldn't this be compatible with any and all outputs? I have a Sony UWP (URX-P41D) receiver.

A: Sennheiser and Sony use the same locking mechanisms, but the internal wiring is different. So, the Cable Techniques Right-Angle Locking 3.5mm TRS to 3.5mm TRS Coiled Cable for Sennheiser should not be used with the Sony URX-P41D Wireless Receiver.

Q: 2. will this work with Blackmagic 7" 12g video assist monitor?

A: No, the IndiPRO Tools D-Tap to Locking 2.1mm DC Right-Angle Cable (24") is not the correct size barrel, as the Blackmagic Design Video Assist 7" 12G-SDI/HDMI HDR Recording Monitor has a 5.5 x 2.5mm DC input. You can use the DigitalFoto Solution Limited D-Tap to 5.5 x 2.5mm DC Barrel Power Cable (36.4") instead. See: https://bhpho.to/2OYfRCg

Q: 3. I’m powering my 702 sound device Need 4pin Hirose x 5.5x2.5

A: This cable is meant for a Lectrosonics system. The cabling you require is dependent on what power source you are coming from. If using a BDS distribution system, here is a cable you could use: https://www.bhphotovideo.com/c/product/283346-REG/Remote_Audio_BDSCSQN_CSQN_BDS_Power_Output.html/specs If from a different power source, I would recommend calling in and speaking with a sales representative for the proper cabling.

Q: 4. Would this be able to power the Atomos Ninja V using the included battery eliminator running off of the IndiPRO Micro Alpha Series 99Wh V-Mount Li-Ion Battery?

A: Yes, the following cable will work to power a Atomos ninja V. I would suggest looking into the following brand to power up you display. https://bhpho.to/3AIiDhJ

Q: 5. Would this work with smallhd Indie 7 locking barrel?

A: Smallhd recommends using their D-Tap to 5.5mm Male DC Barrel Power Cable (3') for use with the Smallhd Indie 7. https://www.bhphotovideo.com/c/product/1154925-REG/smallhd_cbl_pwr_dtap_bar_36_d_tap_adapter_cable.html/qa

Q: 6. Will this work for the Holland Mars 400S?

A: The manufacturer recommends the 'Hollyland D-Tap to 2.1mm Barrel DC Power Cable for Mars 300/400/400S/4K/Cosmo C1' to power the 'Hollyland Mars 400s' via D-tap. The link to this item is below. https://www.bhphotovideo.com/c/product/1564082-REG/hollyland_hl_d_tap_spring_wire_d_tap_to_dc2_1_spring.html

Q: 7. Is this the right cable for the Sound Devices 833?

A: This cable can be connected to the TA4-pin power input port on the Sound Devices 833 digital recorder, if you wish to convert that to RA coaxial male.

Q: 8. Will this also work with Sony UWP-D receivers?

A: Absolutely.

Q: 9. would this power the feelworld f6 plus safly when plugged into the dtap port from the smallrig 99w v mount battery?

A: No, you won't be able to fully insert the DC barrel from the IndiPRO Tools D-Tap to Locking 2.1mm DC Right-Angle Cable (24") into the FeelWorld F6 Plus 5.5" 4K HDMI Monitor since the monitor does not have a locking connector. Consider the Watson Pro D-Tap to 2.1mm Barrel Cable (19") as an alternative cable. The monitor accepts voltages between 7 to 24 volts. See the link below: https://bhpho.to/3zjOvuz

Q: 10. Each of the TA5F ends receives a summed L/R mono - correct? Just confirming this does NOT separate left from right.

A: The Cable Techniques CT-P35RLT2-24 DOES in fact split left and right channels between the two TA5 connectors. The purpose of the cable is to enable transmission of a L/R stereo mix from a 3.5mm source.