Enjoy balanced stereo sound with your amplifier and this pair of ELAC Debut 2.0 OW4.2 2-Way On-Wall Speakers. They feature a 2-way design with a 1" cloth dome tweeter and a 4" woven aramid-fiber cone woofer. Thanks to their down-firing bass ports and included wall mounting brackets, these speakers are specifically designed to be wall-mounted. The OW4.2 speakers accept up to 80W of power from your amplifier, have a 70 Hz to 35 kHz frequency response, and were designed by Andrew Jones.

Designed Specifically for On-Wall Use    Up to 80W Recommended Amplifier Power    2-Way Speaker Design    4" Woven Aramid-Fiber Cone Woofer    1" Cloth Dome Tweeter    70 Hz to 35 kHz Frequency Range    MDF Cabinet    Designed by Andrew Jones

The tweeter features a wide-roll surround and brings response up to 35 kHz for enhanced high frequencies. The waveguide also helps improve directivity control and eliminate the diffraction modes common to speaker enclosures.

The shape of the aramid fiber cone is designed to offer augmented stiffness and damping characteristics over polypropylene or paper cones, helping to achieve a smoother, extended low-frequency response. The woofer also features an oversized magnet and a vented pole piece.

The cabinets are designed for easy integration into your listening room thanks to their shallow depth of less than 4". Their bass-reflex design helps deliver full-frequency performance.

Related Questions and Answers

Q: 1. Can it be wall mounted?

A: Yes. 100 %. 6.2 way to go for wall mount. Put them on wall shelves or hang etc. Important point is the breather is on front.

Q: 2. Will I notice an improvement from the Elac Debut 2.0 6.2?

A: Yes, these are much improved! THWE new series of Debut loudspeakers has been redesigned from the ground up: gone is the rear firing reflex port (now it is a front firing air duct), woofers and tweeters have been replaced by new units and the MDF cabinets have been reinforced to reduce colourations and vibrations. See Elac info here: https://www.elac.com/series/debut-2-0/

Q: 3. Does a Dayton Audio SUB-1000 subwoofer pair with these or not needed for listening to music?

A: I do not see why not. The subwoofer choice is more defined by the size of the room and the the type of music listened to.

Q: 4. Do these ideally need max 120 watt input PER speaker or 120 total?

A: The maximum recommended wattage is 120w per channel.

Q: 5. Will these maintain sound quality if placed on their side tweeter to tweeter. I have limited space.?

A: The ELAC Debut ConneX DCB41 Two-Way Active Bookshelf Speakers (Black Ash, Pair), BH # ELDCB41BK, may be placed on their sides, but will sound best with wider high-end dispersion when oriented vertically.

Q: 6. I ordered ELAC DEBUT B6.2. I have Sony STR-DH190, is there any pronblem with this matching?

A: No problem at all. These ELAC speakers are well matched to the Sony STR-DH190 Stereo Receiver.

Q: 7. CAN I USE ELAC 2.0 A4.2 HAS REAR ATMOS SPEAKERS FOR dobby speaakers?

A: The ELAC Debut 2.0 A4.2 Atmos Add-On Speakers (Pair), BH # ELDA42BK, may be used for the Dolby Atmos channels.

Q: 8. Is the cabinet covered with real wood veneer or vinyl?

A: Elac has confirmed the following.. "The cabinet is a simulated wood look vinyl veneer".

Q: 9. Is a Onkyo TX-8020 Stereo Receiver good for this set?

A: Yes. These ELAC speakers will perform very well with your receiver: Onkyo TX-8020: 50 watts x 2 (stereo) into 8 ohms (20-20,000 Hz) at 0.08% THD

Q: 10. Is Yamaha R-N303D Network Stereo Receiver capable of bringing out the best from this pair of speakers?

A: These are very sensitive 6 ohm speakers. The Yamaha R-N303D, while an excellent receiver, is not designed for 6 ohms, and is less than ideal. It can power the speakers, but could conceivably be damaged at high volume.