The tan H6BMCT H6 Headset Back Mic Clip from Countryman is a replacement back mic clip. It can be used to hold the boom connector on the H6 headset frame (sold separately) for secure placement.

For H6 Headset    Holds Boom Connector to H6 Headset Frame    Secure Placement for Boom

Related Questions and Answers

Q: 1. Can you remove the ten cord and replace it with, say, a silver necklace? Or would metals near the mic cause interference?

A: The necklace cords for the Hollyland Silicone Necklace Case Set with Magnetic Back Clip (Black), BH # HOHLCM02 may be removed.

Q: 2. Do these fit the Samson AirLine Micro?

A: Yes, the On-Stage ASWS20N10 Windscreens should fit on the Samson AirLine Micro AH2 Wireless Earset Transmitter.

Q: 3. will this fit a shure mxl clip on mic?

A: I'm guessing you might either have one of two models, the MX150 or the Motiv MVL, and this is not compatible with either. For MX150 the recommended clip is RPM150TC (3-pack Multi-position Tie Clip) and recommended windscreen is the RPM150WS (package of 3). If you have a Motiv MVL, the recommended snap-in clip is the AMVL-CLIP (1pc), and the windscreen is the AMVL-WS (1pc).

Q: 4. Does tilta sell the thumb screws that secure the three filter stages for their matte box? I've lost one of them!

A: Yes, you can contact Tilta at https://tilta.com/contact/.

Q: 5. will the lavs work with a camcorder?

A: This item is a clip for a B6 Countryman lav mic, which is made to connect to wireless mic systems.

Q: 6. Will the cut out to this case work with the h5n?

A: The H5n is 66mm X 135mm X 42mm and the H6 is 77mm X 152mm X 47mm, so it would be a bit wobbly. You could probably add some foam to make it work

Q: 7. Can you verify that the cable length on this microphone is indeed 13.1' long? I purchased a few of these 3 or 4 years ago and the cable was shorter on those. I prefer the longer cable.

A: 13.1' (4m) cable permanently attached to mic, TA3F connector at power module

Q: 8. Does the MB-T12 has a safety latch or something that prevents the filter trays from falling if you forgot to lock them?

A: When filters are properly inserted into the trays, they will stay in place.

Q: 9. What are dimensions and weight?

A: According to Tilta the matte box is 2.6 lb. Its dimensions are 9.5" X 6". The edge of the lens mount area to the front edge of the matte box is approximately 2.25 inches.

Q: 10. What is the difference between the B and the R models?

A: AT 831b POLAR PATTERNCardioidFREQUENCY RESPONSE40-18,000 HzLOW FREQUENCY ROLL-OFF80 Hz, 18 dB/octaveOPEN CIRCUIT SENSITIVITY Phantom: -44 dB (6.3 mV) re 1V at 1 Pa Battery: -46 dB (5.0 mV) re 1V at 1 PaIMPEDANCEPhantom: 200 ohms Battery: 270 ohmsAT831rPOLAR PATTERNCardioidFREQUENCY RESPONSE40-16,000 HzLOW FREQUENCY ROLL-OFF80 Hz, 18 dB/octaveOPEN CIRCUIT SENSITIVITY Phantom: -44 dB (6.3 mV) re 1V at 1 Pa IMPEDANCEPhantom: 200 ohms Mainly the b has two power sources - battery and phantom power plus a wider freq response, but a shorter cable.