Designed for studio applications that require a balanced cable, the 100' RapcoHorizon 1/4" TRS Male to XLR Male Balanced Cable features hand-soldered Neutrik connectors on both ends and uses Rapco's standard MIC1 wire. The cable is made to provide a quiet, rugged, reliable connection every time.

Hand-Soldered Neutrik Connectors    Rugged Connection and Quiet Performance

24 AWG Conductor

Bare Annealed Copper Serve Shield

95% Shield Coverage

Matte PVC jacket

0.23" Outside Diameter

Capacitance: 1 pF/ft at 1 kHz

Conductor to Shield Capacitance: 37 pF/ft at 1 kHz

Impedance: 70 Ohms

DC Resistance at 68°F: 23 Ohms / 1000 ft

Related Questions and Answers

Q: 1. is this a true TRS? meaning the tip is wired to pin 2, ring is wired to ping 3 and sleeve is pin 1 ? Or is this a pre-summed TRS?

A: This cable is wired straight through. Standard TRS. Pin 2 to Tip, Pin 3 to Ring, Pin 1 - Ground/Shield.

Q: 2. Will this work with a Deity V.Lav mic plugged in to the XLR socket on a Zoom H6?

A: Yes, the VXLR Pro adapter will work with the Deity V.Lav. Deity recommends their D-XLR 3.5mm to XLR Adapter with Phantom to Plug-In Power Conversion (B&H # DXLR) which provides the same type of conversions for the connector and voltage.

Q: 3. Does the use of this cable vs. the stock cable that comes with the G3/G4 receiver affect wireless performance? I ask this because the G3/G4 systems use the output cable as a second antenna.

A: Technically it could it usually is not a problem.

Q: 4. Will this work to connect a Deity V.Lav mic to the XLR input on a Zoom H6?

A: Yes it wll.

Q: 5. Will this work on the Sony transmitters like the D21? I know the polarity of the mic inputs is different to Sennheiser but not sure about the outputs.

A: It is not recommended to use the Cable Techniques Mini TRS to XLR Male Low-Profile Sennheiser Wireless Output Cable (18") with Sony receivers.

Q: 6. Can this adapter be used to connect a Lavignes Mic with the XLR connection directly to the G4 transmitter?

A: This cable is not appropriate for your needs, is for outputting from a wireless receiver to a camera or mixer. If you desire to connect a dynamic mic to a Sennheiser wireless transmitter, i would recommend using a Remote Audio CASENSK100XMC48 XLR Female to Locking 3.5mm TRS Male Adapter Cable (4'), BH #RECASEK100M.

Q: 7. Does B&H sell a locking make 3.5trs to non-locking 3.5trs short cable, as this will be ideal for connecting this adapter to my preferred mic and maximizing connection integrity, at least on the adapter side. Thank you.

A: No. A locking 3.5mm male TRS to a "non-locking" 3.5mm female TRS would be as special order, made to order from a specialty shop, such as Whirlwind. B&H could order for you$$.....

Q: 8. What happens to the -20 safety channel when the Rode VideoMic NTG is used with this "balanced" adapter?

A: When used with a standard unbalanced 3.5mm microphone cable, the Rode VXLR Pro's extra pin (used for inverted polarity audio signal in balanced devices) would be inert, but unbalanced audio is still passed through the balanced connection.

Q: 9. I need to connect a Rode Go ll to a mixer board. What do I need cables or adapters

A: You can use a standard cable with 3.5mm TRS male and XLR male connectors such as the Kopul Stereo Right-Angle 1/8" Male Mini-Jack to XLR Male Cable - 1.5' (B&H # KORSMXM015) to connect the Rode Wireless GO II Receiver to the input on a mixer. Another option is to use an XLR adapter with the 3.5mm TRS cable that is included with the Wireless GO II System. For the XLR adapter, you can use the Rode VXLR 3.5mm TRS Female to XLR Male Adapter (B&H # ROVXLR).

Q: 10. Will it work with my Rode Rodelink filmmaker kit and my Zoom H6?

A: Yes it. will.