The Wooden Camera Pass-Through Top Plate for RED DSMC2 Cameras attaches to the top of your DSMC2 camera using four captive screws and provides additional accessory mounting points. The plate also incorporates the 26-pin LCD and 3-pin trigger connections, passing the signals through to the camera connections. This allows you to mount your RED LCD monitor and Trigger Grip as you would on your camera without the plate while providing multiple threaded accessory mounting points.

The plate incorporates 61 threaded 1/4"-20 mounting holes along the edges and top, as well as two 3/8"-16 threaded holes and 4 x 3/8"-16 threaded mounting holes with ARRI Anti-Twist divots. An additional two 3/8"-16 threaded mounting holes are reserved for use by the LCD connector. The Top Plate is vented, allowing air from your camera's top fans to pass without obstruction.

For DSMC2 BRAINS, WEAPON & RAVEN    Pass-Through Top Plate, Easy Riser Plate    15mm Studio Bridge Plate & 12" Rods    A-Box, Trigger Handle, 12" Dovetail    Ultra Arm Monitor Mount

Related Questions and Answers

Q: 1. Is this compatible with the Ronin DJI RS2 extended baseplate from SmallRig?

A: The Wooden Camera 15mm LWS Baseplate for RED KOMODO bottom could connect to the DJI RS2 lower plate. Please note that the top camera plate is Arca Swiss and could work with the Smaller Upper quick release on the DJI RS2.

Q: 2. Is the camera attached plate an arca swiss mount?

A: The mount is a ARRI Dovetail Clamp.

Q: 3. Where can I get compatible replacement 3/8"-16 screws for this?

A: BH #MAR116.137 are Manfrotto 3/8"-16 Quick Release Plate Screws (2-pack) which you can use with this product. https://bhpho.to/39cKUQh

Q: 4. Do you need the Red Base Expander for this?

A: Hi James. The Base expander is not required to power the camera or to use the functions of this device. However, please note that without it you lack the SDI/HDMI output as well as the ability to monitor audio, jam TC, etc.

Q: 5. Can the Top Handle, Arca-Swiss Mount be mounted on top of the RED Komodo Outrigger Handle?

A: Unfortunately, we have not been able to test these products together, as neither are available in our warehouses as of this writing, and specifications do not explicitly define this pairing.

Q: 6. Will the top mount for the handle and accessory work with the Red Outrigger handle?

A: Unfortunately not, neither allow for mounting of the other.

Q: 7. Is this one compatible with DMSC1 cameras?

A: This is compatible with DMSC2 cameras, it is not designed for DMSC 1 bodies.. For orignal DMSC options you may want to consider the RED DIGITAL CINEMA DSMC Modular Assault Plate Pack, B&H # RE7900224, instead. https://bhpho.to/2WpKW1h

Q: 8. Will this work with the Tilta dovetail vase plate?

A: Yes, this is set up to easily attach to the Tilta Standard Lightweight Dovetail Plate.https://bhpho.to/2s2bwQk

Q: 9. Are there mounting holes on the bottom for attaching a quick release plate? Or do you have to use it with a Tilta dovetail?

A: There are two 1/4" and one 3/8" threads on the bottom along with the Arri style clamp. Pro tip. The Arri style baseplate and dovetail can be tricky to mount and slide. Do NOT apply oil or any lubrication. This will only gather dirt and make the sliding worse. Instead, make sure the pieces are scrupulously clean. Then it will work as intended.

Q: 10. It is compatible with RED Gemini S35 5K ?

A: Yes, this is for DSMC2 bodies. The RED Gemini is a DSMC2 body.