Motorola 2 Way Radio To Xlr

Ati Audio Inc Ada412-xlr Quad 1x3 Low-noise Analog Distribution Amplifier With Xlr Connectors

Product Code: ga62816
Availability: In Stock

$6,555.00 $10,422.45

Qty

3 reviews Write a review

Description
Reviews (3)

The ATI ADA412-XLR is an amplifier capable of routing audio to four 1x3 distribution amplifier channels, all via balanced XLR inputs and outputs. The unit provides a master gain adjustment control for each channel, while individual trimmers are on hand for each output to accommodate gears of various sensitivities over its 20 dB range. Use it to distribute audio in offices, nightclubs, and more.

You're sure to get a low-noise, strong-signal operation out of the ADA412-XLR, as the unit is RF protected to eliminate noise from radio interference. It's also designed to give you pure signal even when you're using lossy cable splitters over long cable runs.

Its automatically ground-sensing active outputs can connect to either balanced or unbalanced loads. In total, the unit provides 4 balanced XLR inputs as well as 12 balanced XLR outputs, divided into four independent channels, with separate input and clipping LEDs for each 1x3 group so you know if you're ever likely to distort audio passing through.

Routes Audio to Four 1x3 Amp Channels Master Gain & Trims for Each Channel RFI Protection to Eliminate Noise Adjustable Input Trim 4 x XLR Inputs 12 x XLR Outputs Rackmountable

Parameters
Output Level	+22 dBm Peak into a 600-Ohm Balanced Load +18 dBm Peak, Typical, into Unbalanced Loads
THD	0.10% Maximum, 20 Hz to 20 kHz at Peak Output
IMD	0.05% Maximum, SMPTE Measurement
Slew Rate	13 V per Microsecond
Response	20 Hz to 20 kHz, ±25 dB
Noise	-95 dBm Out at Maximum Gain, 20 kHz Bandwidth
Gain	40 dB Maximum
Crosstalk	70 dB Minimum at 10 kHz at Any Path
Input Connections	XLR, Female, Active-Balanced, Split, and RF Bypassed
Input Impedance	20 Kilohms
Maximum Input Level	+22 dBm
CMR	60 dB at 60 Hz
Output Isolation	70 dB Minimum at 1 kHz (A Shorted Output Does Not Affect Any Other Output)
Output Connections	XLR, Male, Active Balanced, Servo Controlled, Ground Sensing, DC Coupled
Output Impedance	50 Ohms
Power	85 to 264 VAC ±1%
Output Voltage	24 VDC
Output Power	15 W, 47 to 63 Hz
Dimensions	19 x 1.8 x 7.5" / 48.3 x 4.45 x 19 cm
Packaging Info
Package Weight	9.095 lb
Box Dimensions (LxWxH)	20.8 x 17.1 x 5.8"

The ADA is designed for rack mounting on standard racks. Each unit dissipates approximately 10W and is designed for use in an office environment.

An LF347N quad bi-FET op-amp forms the three variable gain output adjustment stages. These

variable gain stages use a circuit arrangement that allows ATI to provide a smooth,

logarithmic gain control for each output using a linear cermet potentiometer. Since the ADA412 actually reduces the stage gain for low outputs rather than taking the more conventional approach of reducing the input level to a fixed gain amplifier, you can use the ADA at low output levels with very little noise penalty.

ATI has taken measures to keep RFI out of the unit, including split and bypassed input

networks, beaded, bypassed, and isolated power inputs, nonconcentric wound, semi-toroidal

power transformers, double ground plane PC boards, and a quality enclosure to keep rain and

snow off the circuit boards.

Related Questions and Answers

Q: 1. Will my H8 need a firmware update for full functionality with the EXH-8?

A: No firmware upgrade needed- EXH-8 is fully compatible/designed for H8.

Q: 2. Can you recommend a PoE injector to use with this adapter?

A: An injector such as B&H # UBUPOEAT would be suitable to use with the Audinate Dante AVIO 1-Channel XLR Analog Output Adapter for Dante Audio Network.

Q: 3. Do you lose your line in input by using this add-on? Or does it come with it?

A: Yes you will.

Q: 4. Is this a 110 ohm cable thatI can use for my GRIMM MU 1 AEB out to DAC/preamp ?

A: The Grimm Audio Stereo Pair of Audio Cables with XLR Connectors (6.56'), BH # GRSQM2X, is not impedance rated.

Q: 5. The Zoom H8 screen only allows 8 inputs to be recorded and mixed. When the EXH-8 is attached, will the screen show 10 tracks available for simultaneous recording and mixing?

A: Yes, when using the EXH-8 you will see the 10 input tracks with level meters and faders displayed on the screen.

Q: 6. Can the input / output version of these units be used together?

A: It would be helpful to have more details about the application you would be using this for as well as what you are connecting to and from. Please email us at audio@bhphotovideo.com with the information so we can best assist you..

Q: 7. How to find this MAC address

A: The address of Dante devices such as the Audinate Dante AVIO 1-Channel XLR Analog Output Adapter for Dante Audio Network can many times be found on the physical unit itself. Alternatively, the device and address could also be located in the Dane Controller. The article linked here provides further insight: https://bit.ly/3hr4rSI

Q: 8. Is this also compatible with the H5 and H6?

A: At this time, the EXH-8 module is only compatible with the Zoom H8.

Q: 9. Can you charge 4 b-mount batteries simultaneously?

A: Yes. The following unit can simultaneous charger 4 Channel V-Mount batteries.

Q: 10. Can this be used for inputs and outputs at the same time? Or is it just input or just output?

A: The Shure ANI22XLR Audio Network Interface provides two inputs and two outputs, which can be active at the same time.