Print your 3D model in red 5C with the BuMat Elite 1.75mm High-Speed PLA Filament.

PLA filament is made with polymerized lactic acid, which is extracted from corn, sugarcane, or other sugar-containing crops. In addition to being environmentally friendly, this filament also prints at low temperatures, which greatly helps to reduce the possibility of warping. This high-speed PLA filament is recommended for print speeds between 50 to 200mm/s.

1.75mm Filament Diameter    PLA Material    50-200mm/s Optimal Print Speed

Related Questions and Answers

Q: 1. How many full size prints (8x10) or larger can you put in at one time?

A: The Paterson 12x16 High Speed Print Washer has a maximum print size of 12 x 16 in (30.48 x 40.64 cm). The four separators can split that maximum size into three different sizes including: two 6 x 16 inch prints, two 8 x 12 inch prints, or four 6 x 8 inch prints. You can therefore use two 8 x 10 inch prints side-by-side in the 8 x 12 inch separator configuration. It is not designed to stack any prints so only one layer of the two 8 x 10 inch prints is possible.

Q: 2. I read that the sides of the case are reinforced with plastic panels. Is the bottom reinforced also? I don't like it when the bottom of a bag sags from the weight on the gear inside.

A: Yes, the bottom is reinforced with similar stiffness to the sides, but is built in and not removable like the side reinforcement panels.

Q: 3. Will this case fit Dracast LED1000 Pro with yolks on?

A: Yes this case can fit a Dracast LED 100 Pro with the yoke attachment.

Q: 4. What does upgradeable memory mean exactly?

A: The Wave uses a built-in NVME SSD for storage, and the 2TB version allows for 35min of recording time at the above frame rates. The NVME storage is user-exchangeable. So when larger certified drives are available, recording capacity can be increased. Right now it can be ordered with 1TB or 2TB storage.

Q: 5. Where can I see the specs of this camera ? Mount type? Resolution ? Sensor size ? FPS? Etc

A: This camera is E-Mount, Super35 Sensor with Global Shutter, resolutions and frame rates supported are: 4K 422fps, 2K 1461fps, at 2160x128 resolution, 9,259fps. 2TB of storage internally, with 1.5 hours of power. Processes 3,774,873,600 pixels per second with a 5:1 compression.

Q: 6. Will the cards in there plastic cases still fit in the cards slots?

A: You have to remove the SD cards from the plastic cases to fit them in the slots on the Elephant Elite 26 SD Waterproof Hard Memory Card Case (Black Case /Black Foam).

Q: 7. Does this have a drainage hose or does it drain through holes in the tray?

A: The Paterson 8x10" High-Speed Print Washer has an outlet, to which you can attach a hose.

Q: 8. The description says it's meant for RC paper. Can FB prints be washed in this as well?

A: Since RC paper has a tougher base, it can handle the high speed washing. A fiber-based print may be damaged when using it with this washer.

Q: 9. Can the Print Separators be removed.....so i can get 8x10 paper in the tray.?

A: Yes, they pull right out.

Q: 10. Will this fit Lupo Dayled 2000 Dual Color?

A: The Impact LKB-5C Light Kit Bag has an interior dimension of 20.5 x 16.5 x 15.5" / 52.1 x 41.9 x 39.4 cm. The Lupo Dayled PRO 3000 RGB LED Fresnel Light (Manually Operated Yoke) has dimensions of 18.37 x 14.8 x 14.4" / 46.65 x 37.5 x 36.7 cm (Fixture with Mount/Yoke). The light will fit the case.