The Mic Switcher with 3-In/1-Out Microphone Selector Switch from SoundTools allows you to choose between three microphones without using a spare board channel. It is comprised of four 5' XLR cables in a fan design that terminate to a rugged rotary switch and aluminum barrel.

Simply plug in three microphones and easily select between them by rotating the rotary switch. The Mic Switch utilizes a low-noise "make before break" switch, although it is not silent, and a click or pop may be heard, muting the channels before switching is recommended.

Easy to Use 3-Position Rotary Switch    4 x 5' Fan Design    3 x XLR Female, 1 x XLR Male Connectors    Terminated with Neutrik Connectors    Made of Aluminum to Prevent Rust

Related Questions and Answers

Q: 1. Does this cable work for Panasonic Lumix S1R and Zoom H6? Thank you!

A: Hi Edward. For the Zoom H6 recorder, we recommend the LN2MIC-ZOOMH6 or LN2MIC-ZMH6-MON assembly. Thank you!

Q: 2. When switching sources, does it cut or cross-fade? Also, what audio-follow features does it have?

A: This product does not provide a cross fade when switching sources. However you can select to have the audio be Source 1, Source 2, the Master Program or it can swap whatever is set for the master program.

Q: 3. Will the Sescom LN@MIC-TASDR100 work with a Panasonic gh4?

A: Yes, the Sescom LN2MIC-TASDR100 Line Out to Camera Mic Level In Cable will work to adapt a line level output device signal into the microphone input on the Panasonic Lumix GH4 Mirrorless Camera.

Q: 4. Does this work with and it is essential if I want to connect my TASCAM DR-05 to my Canon 7D?

A: In order to connect the output of Your Tascam recorder to the mic input of a DSLR, you will need an attenuator cable such as this Sescom cable. It will allow the camera to receive a safe audio level, and retain headphone monitoring.

Q: 5. This attenuator cable is -25 dB. Other cables are -35dB. What cable is more suitable for Tascam DR40, 40X ?

A: If using this to connect a DR40 into a camera, the -25db cable would be fine to ensure a strong enough level into the preamp of the camera while not overloading it.

Q: 6. This attenuator cable is -25 dB. Other cables are -35dB. What cable is more suitable for Tascam DR40, DR40X ?

A: If using this to connect a DR40 into a camera, the -25db cable would be fine to ensure a strong enough level into the preamp of the camera while not overloading it.

Q: 7. Can I set a custom size/position of the small picture for PIP using the front panel buttons?

A: Unfortunately, the Shinybow 2 x 1 HDMI PiP/PoP Selector Switch Scaler cannot be customized. However, the A-Neuvideo 2x1 HDMI Multi-Viewer with PIP B&H # ANIPIPLITE can be customized via PC software.

Q: 8. is it compatible with Tascam DR-40?

A: Yes, this Sescom cable is compatible for use with the Tascam DR-40 recorder.

Q: 9. Does this cable work for zoom f6 too??

A: Hi Ching. This cable attenuates the signal 35dB, so it might attenuate the signal a bit more than desired. We have a couple of cables specifically for the Zoom H6, the LN2MIC-ZOOMH6 and LN2MIC-ZMH6-MON. These Zoom H6-specific cables attenuate 25dB rather than 35dB. The LN2MIC-TASDR100 cable will work, but you might have to raise the audio level up on your camera if the audio level is a bit low. Thank you!

Q: 10. Hi, Can I connect my zoom H4n to my Panasonic Gh4 with my k6/me66 senhiessen mic for recording into GH4? with this cable.

A: Yes, this cable will be compatible for the setup you describe Sunil.