Add a Picatinny rail for optics or accessories onto your Ruger Mk I or II pistol with this 1-Piece Scope Mount. The mount has pre-drilled screw holes for attachment to the Ruger's receiver.

Picatinny Rail for Ruger Mk I/II    Clamps onto Receiver    Hardened Aluminum

Related Questions and Answers

Q: 1. What is the stop down factor of the textile provided with this kit?

A: Its a 2/3. Check the whats in the box section on the bottom RHS of screen.

Q: 2. what is the stop diffusion for the panel?

A: The Sunbounce Sun-Bouncer Pro Translucent -2/3 Diffuser Screen (4 x 6') (B&H # SUSSBP46T23) included in the Sunbounce Sun-Swatter Pro Starter Kit cuts light by approximately 2/3 stop and does not affect the overall color balance.

Q: 3. Does the grip head allow to connect to a light Stand?

A: I don't recommend it. The slightest wind will send it flying!

Q: 4. I have a Marantz TT 42 turntable that I'm trying to connect to a Mac. This Art DJ PRE II isn't getting it done. No matter what I've tried with changing settings and levels I still have hum and distortion. I've relocated the TT and the MAC to other parts of the house just to see if it might be the power grounding of the house still no help. I had a Rolls VP 29 connecting them fine but it didn't last long at all until the power connection failed. This ART DJ seems to have an issue similar to the Rolls. It also has to have the power connection just right or it crackles and hums terribly. Anyone having the same issue or having any luck connecting a Marantz TT42? With the Rolls I even used it to connect a vintage JVC QL-F61 to several surround receivers and my MAC.

A: The ART DJ Pre II Phono Preamplifier is designed to connect to a stereo receiver or amplifier- The RCA connections provide Line Level Audio, suitable for Line Level inputs only. In/Out Connections RCA Maximum Output Level + 6 dBu (1.4 Vrms) While the Gain may be adusted to reduce the output level to a very low (Mic level), it is not recommended to connect to a Mic level input, as noise, distortion and hum may / will likely be present.

Q: 5. How big is the unit when packaged for transport, in the carry bag?

A: It's small.. Like a backdrop. 4-5!feet long and 5 inches around I would say. Easy to transport.

Q: 6. Can this box be mounted to the RAB-1 rear accessory bracket?

A: Although this is specifically designed to mount via 15mm rods, you should be able to mount via threaded ports as well.

Q: 7. I'm setting up a new turntable and am having trouble with the preamp. From troubleshooting I think it is a problem with the power supply. The original power supply broke, so I replaced it but didn't realize the output amps were slightly higher (output at 2A). Has anyone experienced "sound clipping" because of an overly powerful power supply? Or does the "sound clipping" suggest a different problem?

A: The preamp may be damaged. Please only use the recommended and included power supply.

Q: 8. What is the screw size and thread gauge of the screws that come with this?

A: We connected with Alan Gordon about the screws included with the Alan Gordon Enterprises Hi-Hat and Low-Hat Mounting Board (Pre-Drilled with Screws). Moreover, please note that only Alan Gordon Hi-Hats are compatible with the board. The screws and nuts included are: Cap screw is 3/8 16 by 1 1/4" Hex nut 3/8 16 nut Washers 3/8

Q: 9. Does this come as pictured or with the white laminate?

A: It looks like our current inventory is in this standard finish for the Alan Gordon Enterprises Hi-Hat and Low-Hat Mounting Board (Pre-Drilled with Screws).

Q: 10. Can this power splitting box be used with the Canon C500mk2 by changing the connector to fit the Canon DC IN 12V terminal ?

A: We can only say that the ARRI Gold Mount Power Splitting Box Mk II would work with ARRI ALEXA Mini/Mini LF Cameras.