This 15.7" long 3-Pin Mini-XLR Right-Angle Female to 3-Pin XLR Male Adapter Cable from Ambient Recordings features a female mini-XLR connector where the cable exits the connector to the right, as opposed to the standard straight out the back. The cable is constructed with a braided shield for improved rejection of interference compared to a wrapped foil shield. Instead of PVC, as is common with cheap cables, Ambient uses polyurethane. Even after frequent untwisting and twisting, the plug and cable will not break off.

Cable Exits from Mini-XLR to the Right    Braided Shield    Polyurethane Construction

Related Questions and Answers

Q: 1. Whats the load capacity?

A: The manufactures in general do not list the support weight. The estimate is around 15-20 lbs. But they all recommend using a safety cable. This is a link to some of them, https://bhpho.to/3xKi5bo .

Q: 2. how long is the arm and how long the riser piece?

A: The long part of the Kupo Snap-In Right Angle Pin is approximately 6 inches (14.84 cm) in length, while the shorter 90 riser is approximately 3.6 inches (9.2 cm) in length.

Q: 3. How long is the cable (excluding connectors)?

A: 10 Feet, reasonable with looking at the photo. The listing on Amazon provides the length.

Q: 4. To get additional length to the cable can I add an additional cable such as another XLR cable or another 3.5mm cable? If so will it affect sound quality?

A: You would need to do a calculation based on the electrical characteristics of your cable and the length to ascertain if the loss will be noticeable. But realistically your loss should be negligible using most balanced. I suggest a star quad type cable (4 conductor, shielded individually).

Q: 5. Can you plug two cables into a C70 without the right angle cables blocking each other?

A: unfortunately you can only use oneKondor Blue Right-Angle Mini-XLR Male to XLR Female Cable for BMPCC 6K Pro & Canon C70 (17") on the topport. If you connect the cable on the lower port it blocks the port above.

Q: 6. It lists the 5DMII. Is it compatible with the 5DMIII?

A: The 5DmkII and 5D mkIII feature the same mic input jack. The Sescom cable is compatible with both cameras.

Q: 7. (1) Can you give the specific pin wiring for this cable? I need pins 2-3-1 of the Neutrik XLR wired respectively to the Tip, Ring, and Sleeve of the mini plug for use with a RED Epic microphone input from standard XLR mic out.(2) Is the angle of the cable out of the Neutrik connector user-adjustable to different positions? I would need the cable to outlet at a counterclockwise right angle to the standard configuration shown in the photo.(3) How flexible is the cable? It appears so thick that it would lack malleability in a 1.5 foot length.

A: The Hosa MXM-001.5RS is wired to the standard, Pin 2 to Tip, Pin 3 to Ring, Pin 1 to Sleeve. The XLR connector is non rotating and oriented according to the photo provided. The conductors are 24 gauge allowing some flexibility in the cable.

Q: 8. Does this take the left and right channels from the 3.5mm source and send each separately to the XLR connectors, so that one of the XLRs will be the left channel and the other the right channel?

A: Correct - the left and right stereo signals are split.

Q: 9. Why won't it work with cameras not named here, such as the Vixia HF-G20 camcorder?

A: This cable is actually compatible with any DSLR camera that has a 3.5mm (1/8 ) Stereo Mini Microphone Input.

Q: 10. will it deliver phantom power that Canon 80D generates?

A: The Canon 80 D will not deliver phantom power. It offers a very low voltage known as plug-in power . Power will not be carried over this cable successfully.