The mounts are compatible with VESA compliant displays (75 x 75mm or 100 x 100mm)

Related Questions and Answers

Q: 1. How big can the white board be, top to bottom?

A: AThe Chief OB1U Over-Whiteboard Interactive Display Mount BH #CHOB1U accommodates typical large displays between 42 to 100” and VESA® up to 1020 - 500 mm. (Specify CHIEF FHB7036 or FHB7037 to extend to VESA 1020 x 600 mm) Heavy-duty weight capacity of 310 lbs (140.6 kg) Display height adjustment range of 26” (660 mm) When installed, mount allows for a minimum of 4” (102mm) clearance from wall Overall Dimensions (H x W x D)61.1-75.1 x 55.25 x 6.3” (155.2 – 190.8 x 140.3 x 16 cm)

Q: 2. does this come with screws to attach monitor?

A: Yes, the Premier Mounts PRC-LA Suspension Mount for Flat-Panel Displays (Lower Assembly), B&H # PRPRCLA, includes mounting hardware.

Q: 3. would this mount support SHARP PN-U423 and NEC42 HD prosumer display ?

A: This mount will not work for either of those monitors. You need something that accommodates a larger VESA pattern. This one is good: Chief Flat Panel Single Ceiling Mount (Black) B&H # CHJHSUB MFR # JHSUB

Q: 4. What size poles do these mounts attach to?

A: The Premier Mounts PSD-HDCA Heavy-Duty Clamp Adapter & Flat-Panel Mount (Black), B&H # PRPSDHDCA, is designed to attach to poles with a 2" outer diameter.

Q: 5. Is there a template for mounting

A: NO! Completely unnecessary! Figure the center of where you want the tv, left,right and up,down and mark it with a pencil. Before removing uprights spread them out to max and that is the most they can be mounted apart from each other on the wall. I would subtract an inch to avoid problems. Ideally you want to mount them 22-26 inches apart at the same height. It is all dictated by where your studs are located. Just dont mount to close together, less than 16 inches apart you best keep it centered all the time. Remove the uprights from the crossbars. You can use the same upright to mark both sets of holes. Your template. Use hardware capable of bearing the load(250lbs). If they are mounted at different heights as long as not to much. Half inch or so. There are screws at the top of each to level the bars perfectly. This is probably the BEST TV stand for sale anywhere! GOOD LUCK!!!

Q: 6. Can this support the DELL ULTRASHARP 24 INFINITYEDGE?

A: Hi and thanks for your inquiry - Given the specifications on the Dell website for the Dell UltraSharp 24 InfinityEdge Monitor U2417H- 100mm VESA- 16.2 Lbs. It is certainly within the compatibility range of the LCD-2. Even though the monitor is 24 vs. our stated range of 23 , the mount and monitor will work together.Kind Regards,Keith

Q: 7. Will this work on the dell u2715hc?

A: The Chief KSA1250B-2 Quick-Connect Interface for Select Dell Monitors (Black) BH #CHKSA1250B2 is designed only for those Dell monitors with Dell Quick Release slots and for use exclusively with the Chief Kontour Monitor Arm.

Q: 8. will this bracket work with Nikon d750 & d7200 cameras?

A: Yes. The bracket screws into a standard tripod socket on any brand camera, and any flash will slide into the standard hot shoe. You will need a Nikon connector to communicate between the flash and the hot shoe on your camera body. I bought a Vello, which is much less expensive than a Canon or Nikon. It works just fine.

Q: 9. Can this be easily broken down for transport? Just curious how easy it is to detach a monitor from something like the Premier Mounts PSD-BWL 72" Mobile Nesting Cart. Would like something I could easily put into my car and travel with. Any recommendations for that kind of system?

A: Yes. No special tools required for assembly or dis-assembly.

Q: 10. From the Q&A I understand that the Canon 5D Mkiii with the battery grip will work with this bracket. What is the lens to flash distance with this combo?

A: I have a D750 with grip on the bracket. No problem for the Canon. I'm sure. Not familiar enough with your equipment to give you specific measurements, BUT... If you are trying to eliminate red eye, some shadows and gain off camera versatility, then you have purchased the right piece. Recommend you get the CN JR Anti-twist plate. You will need it, I bet.