The 5' Mains Cable powerCON TRUE1 Top with Bare Ends is a power cord for lights in the ARRI Orbiter Series. This "bare ends" version requires a user-selected plug.

2800-10,000K Variable Color Control    10" Lens    Focusable from 15 to 50 Degrees    Full -Green to Full +Green Control    CRI: 95, TLCI: 91    Onboard DMX, 0-100% Dimmable    Multi-Speed Fan Cooled, On/Off Control    Multi-Voltage: 100-250 VAC, 50/60 Hz    Low 400W Power Consumption, High Output

Related Questions and Answers

Q: 1. Is the 2K output when both color temps are at full? Or is it a full 2K at both 3200 and 5600?

A: According to Dracast, it's half output at either end of the spectrum. When both color temperatures are at full, then you will get full output.

Q: 2. What lamp is needed to run on a 220 circuit?

A: The Impact - FRL (CP/89) Lamp (650W, 220-230V), B&H# IMFRL, or the Sylvania / Osram - FRL (650W/230V) Lamp, B&H# SYFRL, listed under the Accessories tab would be compatible for use with the Arri 650 Plus Fresnel - Hanging, Manual (120-240V AC).

Q: 3. Which one is brighter between this Dracast Fresnel 2000 Bi-Color and Nanlite Forza 500?

A: The Nanlite Forza 500 is brighter

Q: 4. Is the adapter for 220 volts just for the plug or do you need a different adapter for the 220 volt bulb?

A: The power cable and switch for this unit suits both 120v or 220-240v no adaptor required. Therefore you can place any voltage lamp that fits the base of this unit. Obviously the lamp voltage should match the voltage of the country or region where you are using this light.

Q: 5. Which color temp will give the most power? How much power do you lose when toggling between tungsten. daylight and party colors?

A: According to Arri, the output is slightly higher at 5600K. As for using the light in color mode, that would give a similar output to using the light at 5600K, being that there is very minimal color shift.

Q: 6. Is there a burn-in time for this? It smells horrible. Also, when I open it up to full flood, the light shuts off. Is it shorting?

A: this unit like most with a quartz lamp produces a great deal of heat. i would expect some burn-in time. this is a problem made worse in dirty or dusty environments. the fact that you are losing output at full flood raises other questions. i don't think you have a shorting problem (that would overload the circuit feeding the instrument and cause the protective breaker to trip. then there would be no power to illuminate the lamp when you returned to spot or mid-focus positions. it is likely that there is a loose connection in the feed wires which is stretched to the point where contact is broken and is regained when the position of the lamp carriage is moved again. if this is the case there may be a problem with insulation or some other material in the lamphouse touching or getting too near to the lamp (bulb) causing the burning smell.. pop the lamphouse and do some careful inspection of the socket, feed wires and focusing mechanism. be sure unit is unplugged when you do this. i don't want to responsible for your getting a shock if there is an electrical issue.this is not a normal situation and if you can't find a simple explanation quickly it is time to box the unit up and return it for a functional one. in my experience arriflex and b&h are both exceptional service providers and genuinely concerned about quality and customer satisfaction.

Q: 7. Can I fit a lamp softbox on this light?

A: Yes you can use a softbox that's made to withstand heat by getting the correct speed ring under recommended accessories for this fixture.

Q: 8. Can you recommend a hard case that can fit this light? Anything from Pelican ? Thank you.

A: The Pelican 0370 Cube Case without Foam (Black) would be most suitable for this light. https://bhpho.to/2ZK2Lg1

Q: 9. Is there anyway to make these lights produce 5600k instead of 3200k? Is there a lamp compatible for producing daylight for this

A: You can use the Visionsmith ReLamp 1K LED for ARRI ST1, Mole Baby 1K & DeSisti 1K Fresnels (Daylight), BH # VIVSEGTD in place of a standard tungsten halogen lamp. https://bhpho.to/2ZrJxIm

Q: 10. Description says it is dimmable with an external dimmer. What is a suitable dimmer for these lights?

A: For a non professional dimmer you can use # imd1000 or any heavy duty dimmer with an Edison outlet